|
DTC Advanced Diagnostics: SRS related DTCs
SRS Related DTCs
NOTE
|
|
Always check "How to troubleshoot the SRS system" and proceed along each "DTC Troubleshooting" procedure. |
|
|
Make sure the 12 volt battery is fully charged. If not, the results of tests may not be accurate. |
|
|
The SRS indicator will turn on when the battery voltage becomes below 10 volts. |
|
|
The possible causes shown may not be a complete list of all potential problems, and it is possible that there may be other causes. |
DTC B0001-11: Short to Ground in the Driver’s Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground between the SRS unit and the driver’s airbag 1st inflator (LA1+, LA1- lines) |
|
|
Driver’s airbag internal failure (Driver’s airbag 1st inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0001-12: Short to Power in the Driver’s Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to power between the SRS unit and the driver’s airbag 1st inflator (LA1+, LA1- lines) |
|
|
Driver’s airbag internal failure (Driver’s airbag 1st inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0001-13: Open or Increased Resistance in the Driver’s Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the driver’s airbag 1st inflator (LA1+, LA1- lines) |
|
|
Driver’s airbag internal failure (Driver’s airbag 1st inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0001-1A: Decreased Resistance in the Driver’s Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line or Poor connection between the SRS unit and the driver’s airbag 1st inflator (LA1+, LA1- lines) |
|
|
Driver’s airbag internal failure (Driver’s airbag 1st inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0001-2B: Short to Another Wire Harness in the Driver’s Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line between the SRS unit and the driver’s airbag 1st inflator (LA1+ line to LA2+ line, LA1- line to LA2- line) |
|
|
Driver’s airbag internal failure (Driver’s airbag 1st inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0002-11: Short to Ground in the Driver’s Airbag 2nd Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground between the SRS unit and the driver’s airbag 2nd inflator (LA2+, LA2- lines) |
|
|
Driver’s airbag internal failure (Driver’s airbag 2nd inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0002-12: Short to Power in the Driver’s Airbag 2nd Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to power between the SRS unit and the driver’s airbag 2nd inflator (LA2+, LA2- lines) |
|
|
Driver’s airbag internal failure (Driver’s airbag 2nd inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0002-13: Open or Increased Resistance in the Driver’s Airbag 2nd Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the driver’s airbag 2nd inflator (LA2+, LA2- lines) |
|
|
Driver’s airbag internal failure (Driver’s airbag 2nd inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0002-1A: Decreased Resistance in the Driver’s Airbag 2nd Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line or Poor connection between the SRS unit and the driver’s airbag 2nd inflator (LA2+, LA2- lines) |
|
|
Driver’s airbag internal failure (Driver’s airbag 2nd inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0002-2B: Short to Another Wire Harness in the Driver’s Airbag 2nd Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line between the SRS unit and the driver’s airbag 2nd inflator (LA1+ line to LA2+ line, LA1- line to LA2- line) |
|
|
Driver’s airbag internal failure (Driver’s airbag 2nd inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0010-11: Short to Ground in the Front Passenger’s Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground between the SRS unit and the front passenger’s airbag 1st inflator (RA1+, RA1- lines) |
|
|
Front passenger’s airbag internal failure (Front passenger’s airbag 1st inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0010-12: Short to Power in the Front Passenger’s Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to power between the SRS unit and the front passenger’s airbag 1st inflator (RA1+, RA1- lines) |
|
|
SRS unit internal failure | | |
|
DTC B0010-13: Open or Increased Resistance in the Front Passenger’s Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the front passenger’s airbag 1st inflator (RA1+, RA1- lines) |
|
|
Front passenger’s airbag internal failure (Front passenger’s airbag 1st inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0010-1A: Decreased Resistance in the Front Passenger’s Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line or Poor connection between the SRS unit and the front passenger’s airbag 1st inflator (RA1+, RA1- lines) |
|
|
Front passenger’s airbag internal failure (Front passenger’s airbag 1st inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0010-2B: Short to Another Wire Harness in the Front Passenger’s Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line between the SRS unit and the front passenger’s airbag 1st inflator (RA1+, RA1- lines) |
|
|
SRS unit internal failure | | |
|
DTC B0011-11: Short to Ground in the Front Passenger’s Airbag 2nd Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground between the SRS unit and the front passenger’s airbag 2nd inflator (RA2+, RA2- lines) |
|
|
Front passenger’s airbag internal failure (Front passenger’s airbag 2nd inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0011-12: Short to Power in the Front Passenger’s Airbag 2nd Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to power between the SRS unit and the front passenger’s airbag 2nd inflator (RA2+, RA2- lines) |
|
|
SRS unit internal failure | | |
|
DTC B0011-13: Open or Increased Resistance in the Front Passenger’s Airbag 2nd Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the front passenger’s airbag 2nd inflator (RA2+, RA2- lines) |
|
|
Front passenger’s airbag internal failure (Front passenger’s airbag 2nd inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0011-1A: Decreased Resistance in the Front Passenger’s Airbag 2nd Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line or Poor connection between the SRS unit and the front passenger’s airbag 2nd inflator (RA2+, RA2- lines) |
|
|
Front passenger’s airbag internal failure (Front passenger’s airbag 2nd inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0011-2B: Short to Another Wire Harness in the Front Passenger’s Airbag 2nd Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line between the SRS unit and the front passenger’s airbag 2nd inflator (RA2+, RA2- lines) |
|
|
SRS unit internal failure | | |
|
DTC B0020-11: Short to Ground in the Driver’s Side Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground between the SRS unit and the driver’s side airbag inflator (LSA+, LSA- lines) |
|
|
Driver’s side airbag internal failure (Driver’s side airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0020-12: Short to Power in the Driver’s Side Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to power between the SRS unit and the driver’s side airbag inflator (LSA+, LSA- lines) |
|
|
SRS unit internal failure | | |
|
DTC B0020-13: Open or Increased Resistance in the Driver’s Side Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the driver’s side airbag inflator (LSA+, LSA- lines) |
|
|
Driver’s side airbag internal failure (Driver’s side airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0020-1A: Decreased Resistance in the Driver’s Side Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line or Poor connection between the SRS unit and the driver’s side airbag inflator (LSA+, LSA- lines) |
|
|
Driver’s side airbag internal failure (Driver’s side airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0020-2B: Short to Another Wire Harness in the Driver’s Side Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line between the SRS unit and the driver’s side airbag inflator (LSA+, LSA- lines) |
|
|
SRS unit internal failure | | |
|
DTC B0021-11: Short to Ground in the Left Side Curtain Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground between the SRS unit and the left side curtain airbag inflator (LCA+, LCA- lines) |
|
|
Left side curtain airbag internal failure (Left side curtain airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0021-12: Short to Power in the Left Side Curtain Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to power between the SRS unit and the left side curtain airbag inflator (LCA+, LCA- lines) |
|
|
SRS unit internal failure | | |
|
DTC B0021-13: Open or Increased Resistance in the Left Side Curtain Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the left side curtain airbag inflator (LCA+, LCA- lines) |
|
|
Left side curtain airbag internal failure (Left side curtain airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0021-1A: Decreased Resistance in the Left Side Curtain Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line or Poor connection between the SRS unit and the left side curtain airbag inflator (LCA+, LCA- lines) |
|
|
Left side curtain airbag internal failure (Left side curtain airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0021-2B: Short to Another Wire Harness in the Left Side Curtain Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line between the SRS unit and the left side curtain airbag inflator (LCA+, LCA- lines) |
|
|
SRS unit internal failure | | |
|
DTC B0028-11: Short to Ground in the Front Passenger’s Side Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground between the SRS unit and the front passenger’s side airbag inflator (RSA+, RSA- lines) |
|
|
Front passenger’s side airbag internal failure (Front passenger’s side airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0028-12: Short to Power in the Front Passenger’s Side Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to power between the SRS unit and the front passenger’s side airbag inflator (RSA+, RSA- lines) |
|
|
SRS unit internal failure | | |
|
DTC B0028-13: Open or Increased Resistance in the Front Passenger’s Side Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the front passenger’s side airbag inflator (RSA+, RSA- lines) |
|
|
Front passenger’s side airbag internal failure (Front passenger’s side airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0028-1A: Decreased Resistance in the Front Passenger’s Side Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line or Poor connection between the SRS unit and the front passenger’s side airbag inflator (RSA+, RSA- lines) |
|
|
Front passenger’s side airbag internal failure (Front passenger’s side airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0028-2B: Short to Another Wire Harness in the Front Passenger’s Side Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line between the SRS unit and the front passenger’s side airbag inflator (RSA+, RSA- lines) |
|
|
SRS unit internal failure | | |
|
DTC B0029-11: Short to Ground in the Right Side Curtain Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground between the SRS unit and the right side curtain airbag inflator (RCA+, RCA- lines) |
|
|
Right side curtain airbag internal failure (Right side curtain airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0029-12: Short to Power in the Right Side Curtain Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to power between the SRS unit and the right side curtain airbag inflator (RCA+, RCA- lines) |
|
|
SRS unit internal failure | | |
|
DTC B0029-13: Open or Increased Resistance in the Right Side Curtain Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the right side curtain airbag inflator (RCA+, RCA- lines) |
|
|
Right side curtain airbag internal failure (Right side curtain airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0029-1A: Decreased Resistance in the Right Side Curtain Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line or Poor connection between the SRS unit and the right side curtain airbag inflator (RCA+, RCA- lines) |
|
|
Right side curtain airbag internal failure (Right side curtain airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC B0029-2B: Short to Another Wire Harness in the Right Side Curtain Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line between the SRS unit and the right side curtain airbag inflator (RCA+, RCA- lines) |
|
|
SRS unit internal failure | | |
|
DTC B0050-11: Short or Decreased Resistance in the Driver’s Seat Belt Buckle Switch
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground or Short to power between the SRS unit and the driver’s seat belt buckle switch (FLBC line) |
|
|
Driver’s seat belt buckle assembly internal failure (Driver’s seat belt buckle switch) |
|
|
SRS unit internal failure | | |
|
DTC B0050-13: Open or Increased Resistance in the Driver’s Seat Belt Buckle Switch
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the driver’s seat belt buckle switch (FLBC line) |
|
|
Open or Poor connection between the driver’s seat belt buckle switch and the body ground (GND line) |
|
|
Driver’s seat belt buckle assembly internal failure (Driver’s seat belt buckle switch) |
|
|
SRS unit internal failure | | |
|
DTC B0050-2B: Short to Another Wire Harness in the Driver’s Seat Belt Buckle Switch
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line between the SRS unit and the driver’s seat belt buckle switch (FLBC line) |
|
|
Driver’s seat belt buckle assembly internal failure (Driver’s seat belt buckle switch) | | |
|
DTC B0052-11: Short or Decreased Resistance in the Front Passenger’s Seat Belt Buckle Switch
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground or Short to power between the SRS unit and the front passenger’s seat belt buckle switch (FRBC line) |
|
|
Front passenger’s seat belt buckle assembly internal failure (Front passenger’s seat belt buckle switch) |
|
|
SRS unit internal failure | | |
|
DTC B0052-13: Open or Increased Resistance in the Front Passenger’s Seat Belt Buckle Switch
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the front passenger’s seat belt buckle switch (FRBC line) |
|
|
Open or Poor connection between the front passenger’s seat belt buckle switch and the body ground (GND line) |
|
|
Front passenger’s seat belt buckle assembly internal failure (Front passenger’s seat belt buckle switch) |
|
|
SRS unit internal failure | | |
|
DTC B0052-2B: Short to Another Wire Harness in the Front Passenger’s Seat Belt Buckle Switch
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line between the SRS unit and the front passenger’s seat belt buckle switch (FRBC line) |
|
|
Front passenger’s seat belt buckle assembly internal failure (Front passenger’s seat belt buckle switch) | | |
|
DTC B0070-11: Short to Ground in the Driver’s Seat Belt Tensioner
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground between the SRS unit and the driver’s seat belt tensioner (LRP+, LRP- lines) |
|
|
Driver’s seat belt internal failure (Driver’s seat belt tensioner) |
|
|
SRS unit internal failure | | |
|
DTC B0070-12: Short to Power in the Driver’s Seat Belt Tensioner
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to power between the SRS unit and the driver’s seat belt tensioner (LRP+, LRP- lines) |
|
|
SRS unit internal failure | | |
|
DTC B0070-13: Open or Increased Resistance in the Driver’s Seat Belt Tensioner
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the driver’s seat belt tensioner (LRP+, LRP- lines) |
|
|
Driver’s seat belt internal failure (Driver’s seat belt tensioner) |
|
|
SRS unit internal failure | | |
|
DTC B0070-1A: Decreased Resistance in the Driver’s Seat Belt Tensioner
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line or Poor connection between the SRS unit and the driver’s seat belt tensioner (LRP+, LRP- lines) |
|
|
Driver’s seat belt internal failure (Driver’s seat belt tensioner) |
|
|
SRS unit internal failure | | |
|
DTC B0070-2B: Short to Another Wire Harness in the Driver’s Seat Belt Tensioner
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line between the SRS unit and the driver’s seat belt tensioner (LRP+, LRP- lines) |
|
|
SRS unit internal failure | | |
|
DTC B0072-11: Short to Ground in the Front Passenger’s Seat Belt Tensioner
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground between the SRS unit and the front passenger’s seat belt tensioner (RRP+, RRP- lines) |
|
|
Front passenger’s seat belt internal failure (Front passenger’s seat belt tensioner) |
|
|
SRS unit internal failure | | |
|
DTC B0072-12: Short to Power in the Front Passenger’s Seat Belt Tensioner
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to power between the SRS unit and the front passenger’s seat belt tensioner (RRP+, RRP- lines) |
|
|
SRS unit internal failure | | |
|
DTC B0072-13: Open or Increased Resistance in the Front Passenger’s Seat Belt Tensioner
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the front passenger’s seat belt tensioner (RRP+, RRP- lines) |
|
|
Front passenger’s seat belt internal failure (Front passenger’s seat belt tensioner) |
|
|
SRS unit internal failure | | |
|
DTC B0072-1A: Decreased Resistance in the Front Passenger’s Seat Belt Tensioner
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line or Poor connection between the SRS unit and the front passenger’s seat belt tensioner (RRP+, RRP- lines) |
|
|
Front passenger’s seat belt internal failure (Front passenger’s seat belt tensioner) |
|
|
SRS unit internal failure | | |
|
DTC B0072-2B: Short to Another Wire Harness in the Front Passenger’s Seat Belt Tensioner
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line between the SRS unit and the front passenger’s seat belt tensioner (RRP+, RRP- lines) |
|
|
SRS unit internal failure | | |
|
DTC B0090-4A: Internal Failure of the Left Front Impact Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Incorrect left front impact sensor installed |
|
|
Incorrect SRS unit installed |
|
|
Left front impact sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0090-87: No Signal from the Left Front Impact Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the left front impact sensor (LFS+, LFS- lines) |
|
|
Left front impact sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0090-92: Internal Failure of the Left Front Impact Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Left front impact sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0091-4A: Internal Failure of the Left Side Impact Sensor (1st)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Incorrect left side impact sensor (1st) installed |
|
|
Incorrect SRS unit installed |
|
|
Left side impact sensor (1st) internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0091-87: No Signal from the Left Side Impact Sensor (1st)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the left side impact sensor (1st) (LS1+, LS1- lines) |
|
|
Left side impact sensor (1st) internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0091-92: Internal Failure of the Left Side Impact Sensor (1st)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Left side impact sensor (1st) internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0092-4A: Internal Failure of the Left Side Impact Sensor (2nd)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Incorrect left side impact sensor (2nd) installed |
|
|
Incorrect SRS unit installed |
|
|
Left side impact sensor (2nd) internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0092-87: No Signal from the Left Side Impact Sensor (2nd)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the left side impact sensor (2nd) (LS2+, LS2- lines) |
|
|
Left side impact sensor (2nd) internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0092-92: Internal Failure of the Left Side Impact Sensor (2nd)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Left side impact sensor (2nd) internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0093-4A: Internal Failure of the Left Side Impact Sensor (3rd)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Incorrect left side impact sensor (3rd) installed |
|
|
Incorrect SRS unit installed |
|
|
Left side impact sensor (3rd) internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0093-87: No Signal from the Left Side Impact Sensor (3rd)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the left side impact sensor (3rd) (LS3+, LS3- lines) |
|
|
Left side impact sensor (3rd) internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0093-92: Internal Failure of the Left Side Impact Sensor (3rd)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Left side impact sensor (3rd) internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0095-4A: Internal Failure of the Right Front Impact Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Incorrect right front impact sensor installed |
|
|
Incorrect SRS unit installed |
|
|
Right front impact sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0095-87: No Signal from the Right Front Impact Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the right front impact sensor (RFS+, RFS- lines) |
|
|
Right front impact sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0095-92: Internal Failure of the Right Front Impact Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Right front impact sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0096-4A: Internal Failure of the Right Side Impact Sensor (1st)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Incorrect right side impact sensor (1st) installed |
|
|
Incorrect SRS unit installed |
|
|
Right side impact sensor (1st) internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0096-87: No Signal from the Right Side Impact Sensor (1st)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the right side impact sensor (1st) (RS1+, RS1- lines) |
|
|
Right side impact sensor (1st) internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0096-92: Internal Failure of the Right Side Impact Sensor (1st)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Right side impact sensor (1st) internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0097-4A: Internal Failure of the Right Side Impact Sensor (2nd)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Incorrect right side impact sensor (2nd) installed |
|
|
Incorrect SRS unit installed |
|
|
Right side impact sensor (2nd) internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0097-87: No Signal from the Right Side Impact Sensor (2nd)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the right side impact sensor (2nd) (RS2+, RS2- lines) |
|
|
Right side impact sensor (2nd) internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0097-92: Internal Failure of the Right Side Impact Sensor (2nd)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Right side impact sensor (2nd) internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0098-4A: Internal Failure of the Right Side Impact Sensor (3rd)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Incorrect right side impact sensor (3rd) installed |
|
|
Incorrect SRS unit installed |
|
|
Right side impact sensor (3rd) internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0098-87: No Signal from the Right Side Impact Sensor (3rd)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the right side impact sensor (3rd) (RS3+, RS3- lines) |
|
|
Right side impact sensor (3rd) internal failure |
|
|
SRS unit internal failure | | |
|
DTC B0098-92: Internal Failure of the Right Side Impact Sensor (3rd)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Right side impact sensor (3rd) internal failure |
|
|
SRS unit internal failure | | |
|
DTC B00A0-54: Front Passenger's Weight Sensor Not Calibrated
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's weight sensor not initialized |
|
|
Front passenger's weight sensor improper initialization |
|
|
Front passenger's weight sensor internal failure | | |
|
DTC B00A0-87: Lost communication with the SWS Unit
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the front passenger’s weight sensor unit (ODS/SWS ODUS line) |
|
|
Open or Poor connection between the front passenger’s weight sensor unit and the under-dash fuse/relay box (SWS POW line) |
|
|
Open or Poor connection between the front passenger’s weight sensor unit and the body ground (SWS GND line) |
|
|
Blown fuse (Under-dash fuse/relay box No. B6 (7.5A)) |
|
|
Front passenger’s weight sensor unit internal failure |
|
|
SRS unit internal failure | | |
|
DTC B00B5-11: Short or Decreased Resistance in the Driver’s Seat Position Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground between the SRS unit and the driver’s seat position sensor (SS+/LSPS lines) |
|
|
Driver’s seat position sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC B00B5-13: Open or Increased Resistance in the Driver’s Seat Position Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the driver’s seat position sensor (SS+/LSPS lines) |
|
|
Open or Poor connection between the driver’s seat position sensor and the body ground (GND LSPS lines) |
|
|
Driver’s seat position sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC B00B5-2B: Short to Another Wire Harness in the Driver’s Seat Position Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line between the SRS unit and the driver’s seat position sensor (SS+/LSPS lines) |
|
|
Driver’s seat position sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC B00C0-16: Internal Failure of the Front Passenger's Weight Sensor (front inner side)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat frame internal failure (Front passenger's weight sensor (front inner side)) (2-door) |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (front inner side)) (4-door) | | |
|
DTC B00C0-4A: Different Supplier ID/Function ID of the Front Passenger's Weight Sensor (front inner side)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat frame internal failure (Front passenger's weight sensor (front inner side)) (2-door) |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (front inner side)) (4-door) | | |
|
DTC B00C0-54: Different Serial ID of the Front Passenger's Weight Sensor (front inner side)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat frame internal failure (Front passenger's weight sensor (front inner side)) (2-door) |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (front inner side)) (4-door) | | |
|
DTC B00C0-87: No Signal From the Front Passenger's Weight Sensor (front inner side)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open between the SRS unit and the front passenger's weight sensor (front inner side) (SWS+, SWS-, SWSS lines) |
|
|
Short to power between the SRS unit and the front passenger's weight sensor (front inner side) (SWSS line) |
|
|
Short to ground between the SRS unit and the front passenger's weight sensor (front inner side) (SWSS line) |
|
|
Short to another line between the SRS unit and the front passenger's weight sensor (front inner side) (SWSS, SWS- lines) |
|
|
Short to another line between the SRS unit and the front passenger's weight sensor (front inner side) (SWSS, SWS+ lines) |
|
|
SRS unit internal failure | | |
|
DTC B00C0-96: Internal Failure of the Front Passenger's Weight Sensor (front inner side)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat frame internal failure (Front passenger's weight sensor (front inner side)) (2-door) |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (front inner side)) (4-door) | | |
|
DTC B00C1-16: Internal Failure of the Front Passenger's Weight Sensor (front outer side)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat frame internal failure (Front passenger's weight sensor (front outer side)) (2-door) |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (front outer side)) (4-door) | | |
|
DTC B00C1-4A: Different Supplier ID/Function ID of the Front Passenger's Weight Sensor (front outer side)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat frame internal failure (Front passenger's weight sensor (front outer side)) (2-door) |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (front outer side)) (4-door) | | |
|
DTC B00C1-54: Different Serial ID of the Front Passenger's Weight Sensor (front outer side)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat frame internal failure (Front passenger's weight sensor (front outer side)) (2-door) |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (front outer side)) (4-door) | | |
|
DTC B00C1-87: No Signal From the Front Passenger's Weight Sensor (front outer side)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open between the SRS unit and the front passenger's weight sensor (front outer side) (SWS+, SWS-, SWSS lines) |
|
|
SRS unit internal failure | | |
|
DTC B00C1-96: Internal Failure of the Front Passenger's Weight Sensor (front outer side)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat frame internal failure (Front passenger's weight sensor (front outer side)) (2-door) |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (front outer side)) (4-door) | | |
|
DTC B00C2-16: Internal Failure of the Front Passenger's Weight Sensor (rear inner side)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat frame internal failure (Front passenger's weight sensor (rear inner side)) (2-door) |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (rear inner side)) (4-door) | | |
|
DTC B00C2-4A: Different Supplier ID/Function ID of the Front Passenger's Weight Sensor (rear inner side)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat frame internal failure (Front passenger's weight sensor (rear inner side)) (2-door) |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (rear inner side)) (4-door) | | |
|
DTC B00C2-54: Different Serial ID of the Front Passenger's Weight Sensor (rear inner side)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat frame internal failure (Front passenger's weight sensor (rear inner side)) (2-door) |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (rear inner side)) (4-door) | | |
|
DTC B00C2-87: No Signal From the Front Passenger's Weight Sensor (rear inner side)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open between the SRS unit and the front passenger's weight sensor (rear inner side) (SWS+, SWS-, SWSS lines) |
|
|
SRS unit internal failure | | |
|
DTC B00C2-96: Internal Failure of the Front Passenger's Weight Sensor (rear inner side)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat frame internal failure (Front passenger's weight sensor (rear inner side)) (2-door) |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (rear inner side)) (4-door) | | |
|
DTC B00C3-16: Internal Failure of the Front Passenger's Weight Sensor (rear outer side)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat frame internal failure (Front passenger's weight sensor (rear outer side)) (2-door) |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (rear outer side)) (4-door) | | |
|
DTC B00C3-4A: Different Supplier ID/Function ID of the Front Passenger's Weight Sensor (rear outer side)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat frame internal failure (Front passenger's weight sensor (rear outer side)) (2-door) |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (rear outer side)) (4-door) | | |
|
DTC B00C3-54: Different Serial ID of the Front Passenger's Weight Sensor (rear outer side)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat frame internal failure (Front passenger's weight sensor (rear outer side)) (2-door) |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (rear outer side)) (4-door) | | |
|
DTC B00C3-87: No Signal From the Front Passenger's Weight Sensor (rear outer side)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open between the SRS unit and the front passenger's weight sensor (rear outer side) (SWS+, SWS-, SWSS lines) |
|
|
SRS unit internal failure | | |
|
DTC B00C3-96: Internal Failure of the Front Passenger's Weight Sensor (rear outer side)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Front passenger's seat frame internal failure (Front passenger's weight sensor (rear outer side)) (2-door) |
|
|
Front passenger's seat rail internal failure (Front passenger's weight sensor (rear outer side)) (4-door) | | |
|
DTC B00D5-14: Open or Short to Ground in the Front Passenger’s Airbag Cutoff Indicator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 9 seconds. | |
|
Duration |
About 9 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Short to ground between the SRS unit and the front passenger’s airbag cutoff indicator (OFF PTT line) |
|
|
Open or Short to ground between the battery and the front passenger’s airbag cutoff indicator |
|
|
Front passenger’s airbag cutoff indicator internal failure |
|
|
SRS unit internal failure | | |
|
DTC B00D5-17: Short to Power in the Front Passenger’s Airbag Cutoff Indicator
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 9 seconds. | |
|
Duration |
About 9 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to power between the SRS unit and the front passenger’s airbag cutoff indicator (OFF PTT line) |
|
|
Front passenger’s airbag cutoff indicator internal failure |
|
|
SRS unit internal failure | | |
|
DTC B2800-49: Internal Failure of the SRS Unit
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
SRS unit internal failure | | |
|
DTC B2801-49: Internal Failure of the SRS Unit
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
SRS unit internal failure | | |
|
DTC B2802-49: Internal Failure of the SRS Unit
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
SRS unit internal failure | | |
|
DTC B280A-4A: Internal Failure of the Rear Safing Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Incorrect rear safing sensor installed |
|
|
Incorrect SRS unit installed |
|
|
Rear safing sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC B280A-87: No Signal from the Rear Safing Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the rear safing sensor (SSS+, SSS- lines) |
|
|
Rear safing sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC B280A-92: Internal Failure of the Rear Safing Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Rear safing sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC B2840-13: SRS Unit Connector A Not Properly Installed
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Poor connection between the SRS unit and connector A |
|
|
SRS unit internal failure | | |
|
DTC B2841-13: SRS Unit Connector B Not Properly Installed
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Poor connection between the SRS unit and connector B |
|
|
SRS unit internal failure | | |
|
DTC U0101-00: Lost Communication with the PCM (PGM-FI system)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open between the SRS unit and the PCM (F-CAN_H, F-CAN_L lines) |
|
|
SRS unit internal failure | | |
|
DTC U0155-00: Lost Communication with the Gauge Control Module
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open between the SRS unit and the gauge control module (F-CAN_H, F-CAN_L lines) |
|
|
Gauge control module internal failure |
|
|
SRS unit internal failure | | |
|
DTC U3000-49: Internal Failure of the SRS Unit
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
SRS unit internal failure | | |
|
DTC U3000-51: SRS Unit Programming Error
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
SRS unit internal failure | | |
|
DTC U3006-13: Faulty Power Supply (VA line)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open between the SRS unit and the under-dash fuse/relay box (VA line) |
|
|
Blown fuse (Under-dash fuse/relay box No. B6 (7.5A)) |
|
|
SRS unit internal failure | | |
|
DTC U3007-13: Faulty Power Supply (VB line)
|
Confirmation Procedure |
Basic Condition:
|
|
Battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open between the SRS unit and the under-dash fuse/relay box (VB line) |
|
|
Blown fuse (Under-dash fuse/relay box No. B24 (10A)) |
|
|
SRS unit internal failure | | |
| |
