DTC Advanced Diagnostics: P2270
DTC P2270:Secondary Heated Oxygen Sensor (Secondary HO2S (Sensor 2)) Circuit Signal Stuck Lean (Engine Type: K24W1)

General Description


The secondary heated oxygen sensor (secondary HO2S (sensor 2)) detects the oxygen content in the exhaust gas downstream of the three way catalytic converter (TWC) during stoichiometric air/fuel ratio feedback control. The powertrain control module (PCM) controls the air/fuel ratio from the air/fuel ratio (A/F) sensor (sensor 1) output voltage so that the TWC efficiency is optimized. When power is applied to the secondary HO2S (sensor 2) heater, if the secondary HO2S (sensor 2) output continues to be low (lean) during feedback control, the PCM detects a malfunction and stores a DTC.

Monitor Execution, Sequence, Duration, DTC Type, OBD Status
Execution
Continuous
Sequence
None
Duration
30 seconds or more
DTC Type
Two drive cycles, MIL on
OBD Status
PASSED/FAILED/NOT COMPLETED (STILL TESTING)

Enable Conditions
Condition
Minimum
Maximum
Elapsed time that secondary HO2S activity is not monitored after starting the engine
15 seconds
–
Engine coolant temperature
[ECT SENSOR 1]
156 °F (69 °C)
–
Intake air temperature
[IAT SENSOR (2)]
-13 °F (-25 °C)
–
Fuel trim
0.69
1.47
Fuel feedback
Closed loop
No active DTCs set (prevents monitor from running)*1
P0010, P0011, P0087, P0088, P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0117, P0118, P0133, P0134, P0135, P0137, P0138, P0139, P0141, P0171, P0172, P0192, P0193, P0201, P0202, P0203, P0204, P0300, P0301, P0302, P0303, P0304, P0340, P0341, P0344, P0351, P0352, P0353, P0354, P0443, P0496, P0497, P1009, P1128, P1129, P1157, P1172, P145C, P2195, P2238, P2252, P2623, P2646, P2647, P2648, P2649, P2A00
No active DTCs set (prevents monitor from running)*2
P0010, P0011, P0087, P0088, P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0117, P0118, P0122, P0123, P0133, P0134, P0135, P0137, P0139, P0141, P0171, P0172, P0192, P0193, P0201, P0202, P0203, P0204, P0222, P0223, P0300, P0301, P0302, P0303, P0304, P0340, P0341, P0344, P0351, P0352, P0353, P0354, P0443, P0496, P0497, P060A, P1009, P1128, P1129, P1157, P1172, P145C, P1659, P2101, P2118, P2122, P2123, P2127, P2128, P2135, P2138, P2176, P2195, P2238, P2252, P2623, P2646, P2647, P2648, P2649, P2A00
Other
Cruise load or more
*1: 2013 model

*2: 2014 model on and after

[ ]: HDS Parameter

Malfunction Threshold
The secondary HO2S (sensor 2) output voltage [HO2S S2 OUTPUT VOLTAGE] is 0.05 V or less for at least 30 seconds.

Possible Cause
NOTE: The causes shown may not be a complete list of all potential problems, and it is possible that there may be other causes.
Secondary HO2S (sensor 2) lean stuck

Confirmation Procedure
Operating Condition
1.
Start the engine, and let it idle until the radiator fan comes on.
2.
Drive immediately at a steady engine speed [ENGINE SPEED] between 1,500 - 3,000 rpm for at least 30 seconds.
When freeze data is stored, drive the vehicle under those conditions instead of Driving Pattern step 2.
Drive the vehicle in this manner only if the traffic regulations and ambient conditions allow.
With the HDS
None.

Diagnosis Details
Conditions for setting the DTC
When a malfunction is detected during the first drive cycle, a Pending DTC is stored in the PCM memory. If the malfunction returns in the next (second) drive cycle, the MIL comes on and a Confirmed DTC and the freeze data are stored.

Conditions for clearing the DTC
The MIL is cleared if the malfunction does not return in three consecutive trips in which the diagnostic runs. The MIL, the Pending DTC, the Confirmed DTC, and the freeze data can be cleared with the scan tool Clear command or by disconnecting the battery.