Push on the upper hook (A) with the appropriate trim tool, then pull back the inner handle cap (B) to remove it.
2.
Remove the screws (A) securing the front door inner handle.
3.
Pull up the pull pocket cover (A).
4.
Remove the screw.
5.
Pry up the notch (A) and remove the upper grip panel cap (B).
6.
Remove the screw.
7.
Pry up the notch (A) and remove the lower grip panel cap (B).
8.
Remove the screw.
9.
Start at the bottom edge of the front door panel (A), remove the clips (B) with a commercially available trim pad remover.
10.
Starting at the rear, pull the door panel upward.
NOTE: The inner handle cable (C) and the latch cable (D) are connected to the front door inner handle (E). Do not pull up the door panel too far, or these cables will be damaged.
11.
While holding the door panel away from the door, remove the front door inner handle (A) from the door panel by releasing the clips (B).
12.
While holding the front door panel (A) away from the door, remove the harness clip (B) and disconnect the power window switch connector (C) and the courtesy light bulb socket (D).
13.
Driver's side with DPMS: While holding the front door panel away from the door, disconnect the driving position switch connector (E).
3.
Front Door Inner Handle - Remove
Disconnect the inner handle cable (A) and the latch cable (B) from the front door inner handle (C), then remove the handle.
4.
Ornament Panel - Remove
Remove the front door ornament panel (A).
5.
Ornament Grip Panel - Remove
Remove the front door ornament grip panel (A).
6.
Power Window Switch Panel - Remove
1.
Remove the screws (A, B), then remove the power window switch panel (C).
2.
If necessary, remove the front door grip base (A).
7.
Front Door Inner Weatherstrip - Remove
Remove the front door inner weatherstrip (A).
4-Door
1.
Tweeter Cover - Remove
1.
Remove the tweeter cover (A).
2.
Disconnect the tweeter connector (B).
2.
Power Window Switch Panel - Remove
1.
Remove the power window switch panel (A).
2.
Driver's door: Disconnect the power mirror switch connector (B).
3.
Disconnect the power window switch connector (C) and remove the harness clip (D).
3.
Front Door Panel - Remove
1.
Push on the upper hook (A) with the appropriate trim tool, then pull back the inner handle cap (B) to remove it.
2.
Remove the screws (A) securing the front door inner handle.
3.
Remove the screw (A).
4.
Start at the bottom edge of the front door panel (A), remove the clips (B) with a commercially available trim pad remover.
5.
Starting at the rear, pull the door panel upward.
NOTE: The inner handle cable (C) and the latch cable (D) are connected to the front door inner handle (E). Do not pull up the door panel too far, or these cables will be damaged.
6.
While holding the door panel away from the door, remove the front door inner handle (A) from the door panel by releasing the clips (B).
7.
While holding the front door panel (A) away from the door, remove the harness clip (B) and disconnect the courtesy light connector (C).
8.
Driver's side with DPMS: While holding the front door panel away from the door, disconnect the driving position switch connector (D).
4.
Front Door Inner Handle - Remove
Disconnect the inner handle cable (A) and the latch cable (B) from the front door inner handle (C), then remove the handle.
Install the power window switch panel (A), then install the screws (B, C).
3.
Ornament Grip Panel - Install
Install the front door ornament grip panel (A).
4.
Ornament Panel - Install
Install the front door ornament panel (A).
5.
Front Door Inner Handle - Install
Connect the inner handle cable (A) and the latch cable (B) to the front door inner handle (C).
NOTE: If the latch cable and the inner handle cable are damaged or stress-whitened, replace them with new ones.
6.
Front Door Panel - Remove
1.
Driver's side with DPMS: While holding the front door panel (A) away from the door, connect the driving position switch connector (B).
2.
While holding the front door panel away from the door, connect the power window switch connector (C) and the courtesy light bulb socket (D) and install the harness clip (E).
3.
While holding the door panel, install the front door inner handle (A) to the door panel.
4.
Install the front door panel (A).
NOTE: If the latch cable (B) and the inner handle cable (C) are damaged or stress-whitened, replace them with new ones.
5.
Install the screw.
6.
Install the lower grip panel cap (A).
7.
Install the screw.
8.
Install the upper grip panel cap (A).
9.
Install the screw, then install the pull pocket cover (A).
10.
Install the screws (A) securing the front door inner handle.
11.
Install the inner handle cap (A).
7.
Tweeter Cover - Install
1.
Connect the tweeter connector (A).
2.
Install the tweeter cover (B).
4-Door
1.
Front Door Inner Weatherstrip - Install
Install the front door inner weatherstrip (A).
2.
Front Door Armrest - Install
Install the front door armrest (A).
3.
Ornament Panel - Install
Install the front door ornament panel (A).
4.
Front Door Inner Handle - Install
Connect the inner handle cable (A) and the latch cable (B) to the front door inner handle (C).
NOTE: If the latch cable and the inner handle cable are damaged or stress-whitened, replace them with new ones.
5.
Front Door Panel - Install
1.
Driver's side with DPMS: While holding the front door panel (A) away from the door, connect the driving position switch connector (B).
2.
While holding the front door panel away from the door, connect the courtesy light connector (C) and install the harness clip (D).
3.
While holding the door panel, install the front door inner handle (A) to the door panel.
4.
Install the front door panel (A).
NOTE: If the latch cable (B) and the inner handle cable (C) are damaged or stress-whitened, replace them with new ones.
5.
Install the screw (A).
6.
Install the screws (A) securing the front door inner handle.
7.
Install the inner handle cap (A).
6.
Power Window Switch Panel - Install
1.
Driver's door: Connect the power mirror switch connector (A).
2.
Connect the power window switch connector (B) and install the harness clip (C).
