VSA DTC Troubleshooting: 68-11
DTC 68-11: Brake Pedal Position Switch Stuck OFF
NOTE:

DTC Description
DTC
Freeze Frame
68-11 Brake Pedal Position Switch Stuck OFF
    

1.
VSA modulator-control unit performance check:

VSA modulator-control unit performance check
?1.
Start the engine.

?2.
Check the parameter(s) below with the HDS. Do not press the brake pedal.
Signal
Current conditions
Values
Unit
BRAKE PRESSURE
    

Is there 10 MPa or less?

     
YES
     
     
     
Go to step 2.
     
NO
     
     
     
Check for brake drag or a misadjusted brake pedal position switch. If they are normal, go to step 11.
2.
Brake pedal position switch performance check 1:

Brake pedal position switch performance check 1
?1.
Check the parameter(s) below with the HDS while pressing the brake pedal.
Signal
Current conditions
Values
Unit
BRAKE SWITCH
    

Does it indicate ON when the pedal is pressed, and OFF when the pedal is released?

     
YES
     
     
     
Intermittent failure, the system is OK at this time. Refer to intermittent failures troubleshooting.?
     
NO
     
     
     
Go to step 3.
3.
Brake pedal position switch performance check 2:

Brake pedal position switch performance check 2
?1.
Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

?2.
Disconnect the following connector.

?3.
Connect terminals 1 and 2 with a jumper wire.
Terminal 1
Brake pedal position switch 4P connector No. 1 (LT GRN)
Terminal 2
Brake pedal position switch 4P connector No. 2 (PNK)


?4.
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode.

?5.
Check the parameter(s) below with the HDS.
Signal
Current conditions
Values
Unit
BRAKE SWITCH
    

Does it indicate ON?

     
YES
     
     
     
     
NO
     
     
     
Go to step 4.
4.
Fuse check:

Fuse check
?1.
Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

?2.
Disconnect the jumper wire.

?3.
Check the following fuse.
Fuse
No. A6 (10 A)
Location
Under-hood fuse/relay box

Is the fuse OK?

     
YES
     
     
     
The fuse is OK. Reinstall the fuse, then go to step 8.
     
NO
     
     
     
Go to step 5.
5.
Shorted wire check (+B STOP line):

Shorted wire check (+B STOP line)
?1.
Check for continuity between test points 1 and 2.
Test condition
IG LOCK (0) or OFF mode
 
Brake pedal position switch 4P connector: disconnected
Test circuit
+B STOP
Test point 1
Brake pedal position switch 4P connector No. 2 (PNK)
Test point 2
Body ground


Is there continuity?

     
YES
     
     
     
Repair a short to body ground in the wire between the No. A6 (10 A) fuse in the under-hood fuse/relay box and the brake pedal position switch.?
     
NO
     
     
     
The +B STOP wire is not shorted to body ground. Go to step 6.
6.
Shorted wire check (STOP SW line):

Shorted wire check (STOP SW line)
?1.
Short the SCS line with the HDS.


?2.
Disconnect the following connector.

?3.
Check for continuity between test points 1 and 2.
Test condition
IG LOCK (0) or OFF mode
 
Brake pedal position switch 4P connector: disconnected
 
PCM connector A (51P): disconnected
Test circuit
STOP SW
Test point 1
Brake pedal position switch 4P connector No. 1 (LT GRN)
Test point 2
Body ground


Is there continuity?

     
YES
     
     
     
Repair a short to body ground in the wire between the brake pedal position switch and the PCM.?
     
NO
     
     
     
The STOP SW wire is not shorted to body ground. Install a new No. A6 (10 A) fuse in the under-hood fuse/relay box, then go to step 7.
7.
VSA modulator-control unit check:

VSA modulator-control unit check
?1.
Reconnect the following connectors.

?2.
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode.

?3.
Clear the DTC with the HDS.


?4.
Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

?5.
Test-drive the vehicle at 6 mph (10 km/h) or more.
NOTE: Drive the vehicle on the road, not on a lift.

?6.
Check for DTCs with the HDS.
DTC Description
DTC
Freeze Frame
68-11 Brake Pedal Position Switch Stuck OFF
    

Is DTC 68-11 indicated?

     
YES
     
     
     
Go to step 11.
     
NO
     
     
     
The troubleshooting is complete.?
8.
Open wire check (+B STOP line):

Open wire check (+B STOP line)
?1.
Measure the voltage between test points 1 and 2.
Test condition
IG LOCK (0) or OFF mode
 
Brake pedal position switch 4P connector: disconnected
Test circuit
+B STOP
Test point 1
Brake pedal position switch 4P connector No. 2 (PNK)
Test point 2
Body ground


Is there battery voltage?

     
YES
     
     
     
The +B STOP wire is OK. Go to step 9.
     
NO
     
     
     
Repair an open in the wire between the No. A6 (10 A) fuse in the under-hood fuse/relay box and the brake pedal position switch.?
9.
Open wire check (STOP SW line):

Open wire check (STOP SW line)
?1.
Short the SCS line with the HDS.


?2.
Disconnect the following connector.

?3.
Check for continuity between test points 1 and 2.
Test condition
IG LOCK (0) or OFF mode
 
Brake pedal position switch 4P connector: disconnected
 
PCM connector A (51P): disconnected
Test circuit
STOP SW
Test point 1
Brake pedal position switch 4P connector No. 1 (LT GRN)
Test point 2
L4 engine: PCM connector A (51P) No. 37 (LT GRN)
V6 engine: PCM connector A (51P) No. 25 (LT GRN)
L4 engine

V6 engine


Is there continuity?

     
YES
     
     
     
The STOP SW wire is OK. Go to step 10.
     
NO
     
     
     
Repair an open in the wire between the PCM and the brake pedal position switch.?
10.
PCM check (update or substitution):

PCM check (update or substitution)
?1.
Reconnect the following connectors.

?2.
Update the PCM if it does not have the latest software, or substitute a known-good PCM.

?3.
Clear the DTC with the HDS.


?4.
Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

?5.
Test-drive the vehicle at 6 mph (10 km/h) or more.
NOTE: Drive the vehicle on the road, not on a lift.

?6.
Check for DTCs with the HDS.
DTC Description
DTC
Freeze Frame
68-11 Brake Pedal Position Switch Stuck OFF
    

Is DTC 68-11 indicated?

     
YES
     
     
     
Go to step 11.
     
NO
     
     
     
If the PCM was updated, troubleshooting is complete. If the PCM was substituted, replace the original PCM.?
11.
VSA modulator-control unit check (update):

VSA modulator-control unit check (update)
?1.
Update the VSA modulator-control unit if it does not have the latest software.

?2.
Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

?3.
Test-drive the vehicle at 6 mph (10 km/h) or more.
NOTE: Drive the vehicle on the road, not on a lift.

?4.
Check for DTCs with the HDS.
DTC Description
DTC
Freeze Frame
     

Is DTC 68-11 indicated?

     
YES
     
     
     
Check for loose terminals in the VSA modulator-control unit 21P connector. If the VSA modulator-control unit was updated and the symptom/indication is still present, replace the VSA modulator-control unit.?
     
NO
     
     
     
Troubleshooting is complete. If any other DTCs are indicated, go to the indicated DTCs troubleshooting.?