Front Passenger's Power Window Switch Input Test
NOTE:
Before testing, make sure the No. B33 (20 A) fuse in the under-dash fuse/relay box is OK.
Before testing, check for DTCs. If any DTCs are indicated, troubleshoot those DTCs first.

1.
Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

2.
3.
Inspect the connector and socket terminals to be sure they are all making good contact:
If the terminals are bent, loose, or corroded, repair them as necessary, and recheck the system.
If the terminals look OK, go to step 4.

4.
With the connector still disconnected, do the following input tests:
If any test indicates a problem, find and correct the cause, then recheck the system.
If all the input tests prove OK, go to step 5.

Cavity
Wire
Test condition
Test: Desired result
Possible cause if desired result
is not obtained
2
·
1
BLU
·
RED
Connect terminals No. 2 and No. 4, and terminals No. 1 and No. 3 with jumper wires.
Check front passenger's power window motor operation:
The front passenger's power window should close.
Faulty front passenger's power window motor
An open or high resistance in the wire
Connect terminals No. 1 and No. 4, and terminals No. 2 and No. 3 with jumper wires.
Check front passenger's power window motor operation:
The front passenger's power window should open.
27
BLK
Disconnect the front passenger's power window motor 6P connector
Check for continuity between terminal No. 27 and front passenger's power window motor 6P connector terminal No. 4:
There should be continuity.
An open or high resistance in the wire
34
LT BLU
Disconnect the power window master switch 37P connector and the moonroof control unit/motor 14P connector
Check for continuity between terminal No. 34 and power window master switch 37P connector terminal No. 36:
There should be continuity.
An open in the LIN (P/W) wire
Check for continuity between terminal No. 34 and moonroof control unit/motor 14P connector terminal No. 12:
There should be continuity.
An open in the LIN (P/W) wire
Check for continuity to ground:
There should be no continuity.
A short to ground in the LIN (P/W) wire

5.
Reconnect the connector, and do the following input tests:
If any test indicates a problem, find and correct the cause, then recheck the system.
If all the input tests prove OK, replace the front passenger's power window switch.

NOTE: After replacing the front passenger's power window switch, do the resetting the power window control unit.

Cavity
Wire
Test condition
Test: Desired result
Possible cause if desired result
is not obtained
4
GRN
Under all conditions
Measure the voltage to ground:
There should be battery voltage.
Blown No. B33 (20 A) fuse in the under-dash fuse/relay box
An open or high resistance in the wire
3
BLK
In all ignition switch positions or all power modes
Measure the voltage to ground:
There should be less than 0.2 V.
Poor ground (G506)
An open or high resistance in the ground wire
37
PUR
Ignition switch ON (II), or power mode ON
Measure the voltage to ground:
There should be battery voltage.
Faulty front passenger's power window motor
A short to ground in the wire
36
TAN
Ignition switch ON (II), or power mode ON , and front passenger's power window moving up or down
Measure the voltage between terminals No. 36 and No. 3:
An analog meter should alternate between 0 V and 5 V (a digital voltmeter should read about 2.5 V while the window moves).
Faulty front passenger's power window motor
An open or high resistance in the wire
A short to ground in the wire
35
PNK
Ignition switch ON (II), or power mode ON , and front passenger's power window moving up or down
Measure the voltage between terminals No. 35 and No. 3:
An analog meter should alternate between 0 V and 5 V (a digital voltmeter should read about 2.5 V while the window moves).
Faulty front passenger's power window motor
An open or high resistance in the wire
A short to ground in the wire