Audio System Symptom Troubleshooting - Rearview camera image does not change when selecting different views
Rearview camera image does not change when selecting different views
NOTE:
Check the vehicle battery condition first.
You can select three different rearview camera angles for backing up. If there is no camera image on the display, go to Rearview camera image does not come on or work properly troubleshooting.
Check the connectors for poor connections or loose terminals.
1.
Problem verification:

Problem verification
?1.
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode.

?2.
Shift the transmission to R position/mode.

?3.
Operate the audio unit to see if the rearview image changes between the wide view, the normal view, and the top down view in this order.

Does the rearview camera image change properly?

     
YES
     
     
     
Intermittent failure, the system is OK at this time.?
     
NO
     
     
     
The failure is duplicated, go to step 2.
2.
Shorted wire check (CAMERA BIT0 line, CAMERA BIT1 line):

Shorted wire check (CAMERA BIT0 line, CAMERA BIT1 line)
?1.
Shift the transmission to P position/mode or N position/mode.

?2.
Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.

?3.
Disconnect the following connectors.

?4.
Check for continuity between test points 1 and 2.
Test condition
IG LOCK (0) or OFF mode
 
Audio unit connector G (24P): disconnected
 
Rearview camera 8P connector: disconnected
Test circuit
CAMERA BIT0
Test point 1
Audio unit connector G (24P) No. 5 (YEL)
Test point 2
Body ground

Test circuit
CAMERA BIT1
Test point 1
Audio unit connector G (24P) No. 18 (PUR)
Test point 2
Body ground


Is there continuity?

     
YES
     
     
     
Repair a short to body ground in the wire(s) between the audio unit and the rearview camera.?
     
NO
     
     
     
The CAMERA BIT0 and the CAMERA BIT1 wires are not shorted to ground. Go to step 3.
3.
Shorted wire check (CAMERA BIT0 line to CAMERA BIT1 line):

Shorted wire check (CAMERA BIT0 line to CAMERA BIT1 line)
?1.
Check for continuity between test points 1 and 2.
Test condition
IG LOCK (0) or OFF mode
 
Audio unit connector G (24P): disconnected
 
Rearview camera 8P connector: disconnected
Test circuit
CAMERA BIT0, CAMERA BIT1
Test point 1
Audio unit connector G (24P) No. 5 (YEL)
Test point 2
Audio unit connector G (24P) No. 18 (PUR)


Is there continuity?

     
YES
     
     
     
Repair a short in the wire(s) between the audio unit and the rearview camera.?
     
NO: 2-door
     
     
     
The CAMERA BIT0 and the CAMERA BIT1 wires are not shorted. Go to step 4.
     
NO: 4-door
     
     
     
The CAMERA BIT0 and the CAMERA BIT1 wires are not shorted. Go to step 5.
4.
Open wire check (CAMERA BIT0 line, CAMERA BIT1 line):

Open wire check (CAMERA BIT0 line, CAMERA BIT1 line)
?1.
Check for continuity between test points 1 and 2.
Test condition
IG LOCK (0) or OFF mode
 
Audio unit connector G (24P): disconnected
 
Rearview camera 8P connector: disconnected
Test circuit
CAMERA BIT0
Test point 1
Audio unit connector G (24P) No. 5 (YEL)
Test point 2
Rearview camera 8P connector No. 4 (YEL)

Test circuit
CAMERA BIT1
Test point 1
Audio unit connector G (24P) No. 18 (PUR)
Test point 2
Rearview camera 8P connector No. 8 (PUR)


Is there continuity?

     
YES
     
     
     
The CAMERA BIT0 and the CAMERA BIT1 wires are OK. Go to step 6.
     
NO
     
     
     
Repair an open in the wire(s) between the audio unit and the rearview camera.?
5.
Open wire check (CAMERA BIT0 line, CAMERA BIT1 line):

Open wire check (CAMERA BIT0 line, CAMERA BIT1 line)
?1.
Check for continuity between test points 1 and 2.
Test condition
IG LOCK (0) or OFF mode
 
Audio unit connector G (24P): disconnected
 
Rearview camera 8P connector: disconnected
Test circuit
CAMERA BIT0
Test point 1
Audio unit connector G (24P) No. 5 (YEL)
Test point 2
Rearview camera 8P connector No. 3 (YEL)

Test circuit
CAMERA BIT1
Test point 1
Audio unit connector G (24P) No. 18 (PUR)
Test point 2
Rearview camera 8P connector No. 4 (PUR)


Is there continuity?

     
YES
     
     
     
The CAMERA BIT0 and the CAMERA BIT1 wires are OK. Go to step 6.
     
NO
     
     
     
Repair an open in the wire(s) between the audio unit and the rearview camera.?
6.
Rearview camera check (substitution):

Rearview camera check (substitution)
?1.
Substitute a known-good rearview camera.

?2.
Reconnect all the connectors, and recheck.

Does the symptom go away?

     
YES
     
     
     
     
NO