DTC Advanced Diagnostics: SRS related DTCs
SRS Related DTCs
NOTE
Always check "How to troubleshoot the SRS system" and proceed along each "DTC Troubleshooting" procedure.
Make sure the 12 volt battery is fully charged. If not, the results of tests may not be accurate.
The SRS indicator will turn on when the 12 volt battery voltage becomes below 10 volts.
The possible causes shown may not be a complete list of all potential problems, and it is possible that there may be other causes.
DTC B0001-11: Short to Ground in the Driver's Airbag First Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to ground between the SRS unit and the driver's airbag first inflator (LA1+, LA1- lines)
Driver's airbag internal failure (Driver's airbag first inflator)
SRS unit internal failure

DTC B0001-12: Short to Power in the Driver's Airbag First Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to power between the SRS unit and the driver's airbag first inflator (LA1+, LA1- lines)
Driver's airbag internal failure (Driver's airbag first inflator)
SRS unit internal failure

DTC B0001-13: Open or Increased Resistance in the Driver's Airbag First Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open or Poor connection between the SRS unit and the driver's airbag first inflator (LA1+, LA1- lines)
Driver's airbag internal failure (Driver's airbag first inflator)
SRS unit internal failure

DTC B0001-1A: Decreased Resistance in the Driver's Airbag First Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to another line or Poor connection between the SRS unit and the driver's airbag first inflator (LA1+, LA1- lines)
Driver's airbag internal failure (Driver's airbag first inflator)
SRS unit internal failure

DTC B0002-11: Short to Ground in the Driver's Airbag Second Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to ground between the SRS unit and the driver's airbag second inflator (LA2+, LA2- lines)
Driver's airbag internal failure (Driver's airbag second inflator)
SRS unit internal failure

DTC B0002-12: Short to Power in the Driver's Airbag Second Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to power between the SRS unit and the driver's airbag second inflator (LA2+, LA2- lines)
Driver's airbag internal failure (Driver's airbag second inflator)
SRS unit internal failure

DTC B0002-13: Open or Increased Resistance in the Driver's Airbag Second Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open or Poor connection between the SRS unit and the driver's airbag second inflator (LA2+, LA2- lines)
Driver's airbag internal failure (Driver's airbag second inflator)
SRS unit internal failure

DTC B0002-1A: Decreased Resistance in the Driver's Airbag Second Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to another line or Poor connection between the SRS unit and the driver's airbag second inflator (LA2+, LA2- lines)
Driver's airbag internal failure (Driver's airbag second inflator)
SRS unit internal failure

DTC B0010-11: Short to Ground in the Front Passenger's Airbag First Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to ground between the SRS unit and the front passenger's airbag first inflator (RA1+, RA1- lines)
Front passenger's airbag internal failure (Front passenger's airbag first inflator)
SRS unit internal failure

DTC B0010-12: Short to Power in the Front Passenger's Airbag First Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to power between the SRS unit and the front passenger's airbag first inflator (RA1+, RA1- lines)
SRS unit internal failure

DTC B0010-13: Open or Increased Resistance in the Front Passenger's Airbag First Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open or Poor connection between the SRS unit and the front passenger's airbag first inflator (RA1+, RA1- lines)
Front passenger's airbag internal failure (Front passenger's airbag first inflator)
SRS unit internal failure

DTC B0010-1A: Decreased Resistance in the Front Passenger's Airbag First Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to another line or Poor connection between the SRS unit and the front passenger's airbag first inflator (RA1+, RA1- lines)
Front passenger's airbag internal failure (Front passenger's airbag first inflator)
SRS unit internal failure

DTC B0011-11: Short to Ground in the Front Passenger's Airbag Second Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to ground between the SRS unit and the front passenger's airbag second inflator (RA2+, RA2- lines)
Front passenger's airbag internal failure (Front passenger's airbag second inflator)
SRS unit internal failure

DTC B0011-12: Short to Power in the Front Passenger's Airbag Second Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to power between the SRS unit and the front passenger's airbag second inflator (RA2+, RA2- lines)
SRS unit internal failure

DTC B0011-13: Open or Increased Resistance in the Front Passenger's Airbag Second Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open or Poor connection between the SRS unit and the front passenger's airbag second inflator (RA2+, RA2- lines)
Front passenger's airbag internal failure (Front passenger's airbag second inflator)
SRS unit internal failure

DTC B0011-1A: Decreased Resistance in the Front Passenger's Airbag Second Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to another line or Poor connection between the SRS unit and the front passenger's airbag second inflator (RA2+, RA2- lines)
Front passenger's airbag internal failure (Front passenger's airbag second inflator)
SRS unit internal failure

DTC B0020-11: Short to Ground in the Driver's Side Airbag Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to ground between the SRS unit and the driver's side airbag inflator (LSA+, LSA- lines)
Driver's side airbag internal failure (Driver's side airbag inflator)
SRS unit internal failure

DTC B0020-12: Short to Power in the Driver's Side Airbag Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to power between the SRS unit and the driver's side airbag inflator (LSA+, LSA- lines)
SRS unit internal failure

DTC B0020-13: Open or Increased Resistance in the Driver's Side Airbag Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open or Poor connection between the SRS unit and the driver's side airbag inflator (LSA+, LSA- lines)
Driver's side airbag internal failure (Driver's side airbag inflator)
SRS unit internal failure

DTC B0020-1A: Decreased Resistance in the Driver's Side Airbag Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to another line or Poor connection between the SRS unit and the driver's side airbag inflator (LSA+, LSA- lines)
Driver's side airbag internal failure (Driver's side airbag inflator)
SRS unit internal failure

DTC B0021-11: Short to Ground in the Left Side Curtain Airbag First Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to ground between the SRS unit and the left side curtain airbag inflator (LCA+, LCA- lines)
Left side curtain airbag internal failure (Left side curtain airbag inflator)
SRS unit internal failure

DTC B0021-12: Short to Power in the Left Side Curtain Airbag First Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to power between the SRS unit and the left side curtain airbag inflator (LCA+, LCA- lines)
SRS unit internal failure

DTC B0021-13: Open or Increased Resistance in the Left Side Curtain Airbag First Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open or Poor connection between the SRS unit and the left side curtain airbag inflator (LCA+, LCA- lines)
Left side curtain airbag internal failure (Left side curtain airbag inflator)
SRS unit internal failure

DTC B0021-1A: Decreased Resistance in the Left Side Curtain Airbag First Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to another line or Poor connection between the SRS unit and the left side curtain airbag inflator (LCA+, LCA- lines)
Left side curtain airbag internal failure (Left side curtain airbag inflator)
SRS unit internal failure

DTC B0028-11: Short to Ground in the Front Passenger's Side Airbag Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to ground between the SRS unit and the front passenger's side airbag inflator (RSA+, RSA- lines)
Front passenger's side airbag internal failure (Front passenger's side airbag inflator)
SRS unit internal failure

DTC B0028-12: Short to Power in the Front Passenger's Side Airbag Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to power between the SRS unit and the front passenger's side airbag inflator (RSA+, RSA- lines)
SRS unit internal failure

DTC B0028-13: Open or Increased Resistance in the Front Passenger's Side Airbag Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open or Poor connection between the SRS unit and the front passenger's side airbag inflator (RSA+, RSA- lines)
Front passenger's side airbag internal failure (Front passenger's side airbag inflator)
SRS unit internal failure

DTC B0028-1A: Decreased Resistance in the Front Passenger's Side Airbag Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to another line or Poor connection between the SRS unit and the front passenger's side airbag inflator (RSA+, RSA- lines)
Front passenger's side airbag internal failure (Front passenger's side airbag inflator)
SRS unit internal failure

DTC B0029-11: Short to Ground in the Right Side Curtain Airbag First Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to ground between the SRS unit and the right side curtain airbag inflator (RCA+, RCA- lines)
Right side curtain airbag internal failure (Right side curtain airbag inflator)
SRS unit internal failure

DTC B0029-12: Short to Power in the Right Side Curtain Airbag First Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to power between the SRS unit and the right side curtain airbag inflator (RCA+, RCA- lines)
SRS unit internal failure

DTC B0029-13: Open or Increased Resistance in the Right Side Curtain Airbag First Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open or Poor connection between the SRS unit and the right side curtain airbag inflator (RCA+, RCA- lines)
Right side curtain airbag internal failure (Right side curtain airbag inflator)
SRS unit internal failure

DTC B0029-1A: Decreased Resistance in the Right Side Curtain Airbag First Inflator
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to another line or Poor connection between the SRS unit and the right side curtain airbag inflator (RCA+, RCA- lines)
Right side curtain airbag internal failure (Right side curtain airbag inflator)
SRS unit internal failure

DTC B0050-11: Short or Decreased Resistance in the Driver's Seat Belt Buckle Switch
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to ground or Short to power between the SRS unit and the driver's seat belt buckle switch (FLBC line)
Driver's seat belt buckle assembly internal failure (Driver's seat belt buckle switch)
SRS unit internal failure

DTC B0050-13: Open or Increased Resistance in the Driver's Seat Belt Buckle Switch
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open or Poor connection between the SRS unit and the driver's seat belt buckle switch (FLBC line)
Open or Poor connection between the driver's seat belt buckle switch and the body ground (GND line)
Driver's seat belt buckle assembly internal failure (Driver's seat belt buckle switch)
SRS unit internal failure

DTC B0052-11: Short or Decreased Resistance in the Front Passenger's Seat Belt Buckle Switch
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to ground or Short to power between the SRS unit and the front passenger's seat belt buckle switch (FRBC line)
Front passenger's seat belt buckle assembly internal failure (Front passenger's seat belt buckle switch)
SRS unit internal failure

DTC B0052-13: Open or Increased Resistance in the Front Passenger's Seat Belt Buckle Switch
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open or Poor connection between the SRS unit and the front passenger's seat belt buckle switch (FRBC line)
Open or Poor connection between the front passenger's seat belt buckle switch and the body ground (GND line)
Front passenger's seat belt buckle assembly internal failure (Front passenger's seat belt buckle switch)
SRS unit internal failure

DTC B0070-11: Short to Ground in the Driver's Seat Belt Tensioner
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to ground between the SRS unit and the driver's seat belt tensioner (LRP+, LRP- lines)
Driver's seat belt internal failure (Driver's seat belt tensioner)
SRS unit internal failure

DTC B0070-12: Short to Power in the Driver's Seat Belt Tensioner
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to power between the SRS unit and the driver's seat belt tensioner (LRP+, LRP- lines)
SRS unit internal failure

DTC B0070-13: Open or Increased Resistance in the Driver's Seat Belt Tensioner
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open or Poor connection between the SRS unit and the driver's seat belt tensioner (LRP+, LRP- lines)
Driver's seat belt internal failure (Driver's seat belt tensioner)
SRS unit internal failure

DTC B0070-1A: Decreased Resistance in the Driver's Seat Belt Tensioner
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to another line or Poor connection between the SRS unit and the driver's seat belt tensioner (LRP+, LRP- lines)
Driver's seat belt internal failure (Driver's seat belt tensioner)
SRS unit internal failure

DTC B0072-11: Short to Ground in the Front Passenger's Seat Belt Tensioner
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to ground between the SRS unit and the front passenger's seat belt tensioner (RRP+, RRP- lines)
Front passenger's seat belt internal failure (Front passenger's seat belt tensioner)
SRS unit internal failure

DTC B0072-12: Short to Power in the Front Passenger's Seat Belt Tensioner
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to power between the SRS unit and the front passenger's seat belt tensioner (RRP+, RRP- lines)
SRS unit internal failure

DTC B0072-13: Open or Increased Resistance in the Front Passenger's Seat Belt Tensioner
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open or Poor connection between the SRS unit and the front passenger's seat belt tensioner (RRP+, RRP- lines)
Front passenger's seat belt internal failure (Front passenger's seat belt tensioner)
SRS unit internal failure

DTC B0072-1A: Decreased Resistance in the Front Passenger's Seat Belt Tensioner
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to another line or Poor connection between the SRS unit and the front passenger's seat belt tensioner (RRP+, RRP- lines)
Front passenger's seat belt internal failure (Front passenger's seat belt tensioner)
SRS unit internal failure

DTC B0090-4A: Internal Failure of the Left Front Impact Sensor
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Incorrect impact sensor installed
Incorrect SRS unit installed
Left front impact sensor internal failure
SRS unit internal failure

DTC B0090-87: No Signal From the Left Front Impact Sensor
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the left front impact sensor (LFS+, LFS- lines)
Left front impact sensor internal failure
SRS unit internal failure

DTC B0090-92: Internal Failure of the Left Front Impact Sensor
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Left front impact sensor internal failure
SRS unit internal failure

DTC B0091-4A: Internal Failure of the Left Side Impact Sensor (first)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Incorrect impact sensor installed
Incorrect SRS unit installed
Left side impact sensor (first) internal failure
SRS unit internal failure

DTC B0091-87: No Signal From the Left Side Impact Sensor (first)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the left side impact sensor (first) (LS1+, LS1- lines)
Left side impact sensor (first) internal failure
SRS unit internal failure

DTC B0091-92: Internal Failure of the Left Side Impact Sensor (first)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Left side impact sensor (first) internal failure
SRS unit internal failure

DTC B0092-4A: Internal Failure of the Left Side Impact Sensor (second)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Incorrect impact sensor installed
Incorrect SRS unit installed
Left side impact sensor (second) internal failure
SRS unit internal failure

DTC B0092-87: No Signal From the Left Side Impact Sensor (second)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the left side impact sensor (second) (LS2+, LS2- lines)
Left side impact sensor (second) internal failure
SRS unit internal failure

DTC B0092-92: Internal Failure of the Left Side Impact Sensor (second)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Left side impact sensor (second) internal failure
SRS unit internal failure

DTC B0095-4A: Internal Failure of the Right Front Impact Sensor
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Incorrect impact sensor installed
Incorrect SRS unit installed
Right front impact sensor internal failure
SRS unit internal failure

DTC B0095-87: No Signal From the Right Front Impact Sensor
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the right front impact sensor (RFS+, RFS- lines)
Right front impact sensor internal failure
SRS unit internal failure

DTC B0095-92: Internal Failure of the Right Front Impact Sensor
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Right front impact sensor internal failure
SRS unit internal failure

DTC B0096-4A: Internal Failure of the Right Side Impact Sensor (first)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Incorrect impact sensor installed
Incorrect SRS unit installed
Right side impact sensor (first) internal failure
SRS unit internal failure

DTC B0096-87: No Signal From the Right Side Impact Sensor (first)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the right side impact sensor (first) (RS1+, RS1- lines)
Right side impact sensor (first) internal failure
SRS unit internal failure

DTC B0096-92: Internal Failure of the Right Side Impact Sensor (first)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Right side impact sensor (first) internal failure
SRS unit internal failure

DTC B0097-4A: Internal Failure of the Right Side Impact Sensor (second)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Incorrect impact sensor installed
Incorrect SRS unit installed
Right side impact sensor (second) internal failure
SRS unit internal failure

DTC B0097-87: No Signal From the Right Side Impact Sensor (second)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the right side impact sensor (second) (RS2+, RS2- lines)
Right side impact sensor (second) internal failure
SRS unit internal failure

DTC B0097-92: Internal Failure of the Right Side Impact Sensor (second)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Right side impact sensor (second) internal failure
SRS unit internal failure

DTC B00A0-54: Front Passenger's Weight Sensor not Calibrated
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Front passenger's weight sensor not initialized

DTC B00B5-11: Short or Decreased Resistance in the Driver's Seat Position Sensor
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to ground between the SRS unit and the driver's seat position sensor (SPS/SS+ SPS line)
Driver's seat position sensor internal failure
SRS unit internal failure

DTC B00B5-13: Open or Increased Resistance in the Driver's Seat Position Sensor
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open or Poor connection between the SRS unit and the driver's seat position sensor (SPS/SS+ SPS line)
Open or Poor connection between the driver's seat position sensor and the body ground (GND/GND SPS line)
Driver's seat position sensor internal failure
SRS unit internal failure

DTC B00C0-16: Internal Failure of the Front Passenger's Weight Sensor (front inner side)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Front passenger's weight sensor internal failure (front inner side)

DTC B00C0-4A: Different Supplier ID/Function ID of the Front Passenger's Weight Sensor (front inner side)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Front passenger's weight sensor internal failure (front inner side)

DTC B00C0-54: Different Serial ID of the Front Passenger's Weight Sensor (front inner side)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Front passenger's weight sensor internal failure (front inner side)

DTC B00C0-87: No Signal From the Front Passenger's Weight Sensor (front inner side)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open or Poor connection between the SRS unit and the front passenger's weight sensor (front inner side) (SWS+/PWR SWS, SWS-/GND SWS, SWSS/LIN SWS lines)
Short to power or Short to ground between the SRS unit and the front passenger's weight sensor (front inner side) (SWSS/LIN SWS line)
Short to another line or Poor connection between the SRS unit and the front passenger's weight sensor (front inner side) (SWSS/LIN SWS line to SWS-/GND SWS line, SWSS/LIN SWS line to SWS+/PWR SWS line)
SRS unit internal failure

DTC B00C0-96: Internal Failure of the Front Passenger's Weight Sensor (front inner side)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Front passenger's weight sensor internal failure (front inner side)

DTC B00C2-16: Internal Failure of the Front Passenger's Weight Sensor (rear inner side)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Front passenger's weight sensor internal failure (rear inner side)

DTC B00C2-4A: Different Supplier ID/Function ID of the Front Passenger's Weight Sensor (rear inner side)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Front passenger's weight sensor internal failure (rear inner side)

DTC B00C2-54: Different Serial ID of the Front Passenger's Weight Sensor (rear inner side)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Front passenger's weight sensor internal failure (rear inner side)

DTC B00C2-87: No Signal From the Front Passenger's Weight Sensor (rear inner side)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open or Poor connection between the SRS unit and the front passenger's weight sensor (rear inner side) (SWS+/PWR SWS, SWS-/GND SWS, SWSS/LIN SWS lines)
SRS unit internal failure

DTC B00C2-96: Internal Failure of the Front Passenger's Weight Sensor (rear inner side)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Front passenger's weight sensor internal failure (rear inner side)

DTC B00D5-14: Open or Short to Ground in the Front Passenger's Airbag Cutoff Indicator (USA and Canada models)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 9 seconds.
Duration
About 9 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open or Short to ground between the SRS unit and the front passenger's airbag cutoff indicator (OFF PTT line)
Open or Short to ground between the 12 volt battery and the front passenger's airbag cutoff indicator
Front passenger's airbag cutoff indicator internal failure
SRS unit internal failure

DTC B00D5-14: Open or Short to Ground in the Front Passenger's Airbag ON/OFF Indicator (Mexico models)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 9 seconds.
Duration
About 9 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open or Short to ground between the SRS unit and the front passenger's airbag ON/OFF indicator (OFF PTT line)
Open or Short to ground between the 12 volt battery and the front passenger's airbag ON/OFF indicator
Front passenger's airbag ON/OFF indicator internal failure
SRS unit internal failure

DTC B00D5-17: Short to Power in the Front Passenger's Airbag Cutoff Indicator (USA and Canada models)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 9 seconds.
Duration
About 9 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to power between the SRS unit and the front passenger's airbag cutoff indicator (OFF PTT line)
Front passenger's airbag cutoff indicator internal failure
SRS unit internal failure

DTC B00D5-17: Short to Power in the Front Passenger's Airbag ON/OFF Indicator (Mexico models)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 9 seconds.
Duration
About 9 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to power between the SRS unit and the front passenger's airbag ON/OFF indicator (OFF PTT line)
Front passenger's airbag ON/OFF indicator internal failure
SRS unit internal failure

DTC B00DF-11: Short in the Front Passenger's Airbag ON/OFF Switch
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 9 seconds.
Duration
About 9 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to ground between the SRS unit and the front passenger's airbag ON/OFF switch (ACS line)
Front passenger's airbag ON/OFF switch internal failure
SRS unit internal failure

DTC B00DF-13: Open in the Front Passenger's Airbag ON/OFF Switch
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 9 seconds.
Duration
About 9 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open or Short to power between the SRS unit and the front passenger's airbag ON/OFF switch (ACS line)
Open or Short to power between the front passenger's airbag ON/OFF switch and the body ground (GND line)
Front passenger's airbag ON/OFF switch internal failure
SRS unit internal failure

DTC B2800-49: Internal Failure of the SRS Unit
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
SRS unit internal failure

DTC B2801-49: Internal Failure of the SRS Unit
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
SRS unit internal failure

DTC B2802-49: Internal failure of the SRS unit
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
SRS unit internal failure

DTC B2840-13: SRS Unit Connector A Not Properly Installed
DTC B2841-13: SRS Unit Connector B Not Properly Installed
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Poor connection between the SRS unit and connector A or poor connection between the SRS unit and connector B
SRS unit internal failure
NOTE: If a loose connection failure occurs, DTC B2840-13 and B2841-13 are stored at same time to the SRS unit.

DTC C0061-96: Internal Failure of the SRS Unit
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
SRS unit internal failure

DTC U0122-00: Lost Communication With the VSA Modulator-Control Unit (wheel speed sensor signal error) (Without CAN Gateway)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open or Poor connection between the VSA modulator-control unit and the SRS unit (F-CAN_H, F-CAN_L lines)
VSA modulator-control unit internal failure

DTC U0122-00: Lost Communication With the VSA Modulator-Control Unit (wheel speed sensor signal error) (With CAN Gateway)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Open or Poor connection between the CAN gateway and the SRS unit (F-CAN B_H, F-CAN B_L lines)
Open or Poor connection between the CAN gateway and the VSA modulator-control unit (F-CAN A_H, F-CAN A_L, F-CAN B_H, F-CAN B_L lines)
VSA modulator-control unit internal failure
SRS unit internal failure

DTC U3000-49: Internal Failure of the SRS Unit (USA and Canada models)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
Short to ground or Short to power between the SRS unit and the front passenger's weight sensor (front inner side) (SWS+/PWR SWS line)
Short to another line between the SRS unit and the front passenger's weight sensor (front inner side) (SWS+/PWR SWS line to SWS-/GND SWS line)
Short to ground or Short to power between the SRS unit and the front passenger's weight sensor (rear inner side) (SWS+/PWR SWS line)
Short to another line between the SRS unit and the front passenger's weight sensor (rear inner side) (SWS+/PWR SWS line to SWS-/GND SWS line)
SRS unit internal failure

DTC U3000-49: Internal Failure of the SRS Unit (Mexico models)
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
SRS unit internal failure

DTC U3000-51: SRS Unit Programming Error
Confirmation Procedure
Basic Condition:
12 volt battery voltage 10 - 16 V

Operating Condition:
1.
Turn the vehicle to the ON mode, and wait 6 seconds.
Duration
About 6 seconds
DTC Type
1 drive cycle
SRS indicator on
Fail Safe Action
None
Possible Cause
SRS unit update is not completed properly
SRS unit internal failure