DTC Troubleshooting: P0717
DTC P0717: Input/Turbine Speed Sensor "A" Circuit No Signal
NOTE:
Before you troubleshoot, review the General Troubleshooting Information.
This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the transmission.

DTC Description
Confirmed DTC
Pending DTC
Freeze Frame
P0717 Input/Turbine Speed Sensor "A" Circuit No Signal
      

1.
Problem verification:

Problem verification
?1.
Turn the vehicle to the ON mode.

?2.
Clear the DTC with the HDS.


?3.
Raise the vehicle on a lift. Make sure it is securely supported, and allow all four wheels to rotate freely.

?4.
Start the engine, disable the VSA by pressing the VSA OFF button.
NOTE: Enter the VSA maintenance mode in case of the vehicle speed above 31 mph (50 km/h).

?5.
Run the vehicle at speeds over 19 mph (30 km/h) for at least 30 seconds. Slow down, and stop the wheels.

?6.
Check for Pending or Confirmed DTCs with the HDS.
DTC Description
Confirmed DTC
Pending DTC
Freeze Frame
P0717 Input/Turbine Speed Sensor "A" Circuit No Signal
      

Is DTC P0717 indicated?

     
YES
     
     
     
The failure is duplicated. Go to step 2.
     
NO
     
     
     
Intermittent failure, the system is OK at this time. Check for poor connections and loose terminals between the torque converter turbine speed sensor and the TCM. If the freeze data/on-board snapshot of this DTC is recorded, try to reproduce the failure under the same conditions with the freeze data/onboard snapshot.?
2.
Determine possible failure area (NT line, others):

Determine possible failure area (NT line, others)
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Disconnect the following connector.
Torque converter turbine speed sensor 3P connector

?3.
Turn the vehicle to the ON mode.

?4.
Measure the voltage between test points 1 and 2.
Test condition
Vehicle ON mode
 
Torque converter turbine speed sensor 3P connector: disconnected
Test point 1
Torque converter turbine speed sensor 3P connector No. 2
Test point 2
Body ground


Is there about 5 V?

     
YES
     
     
     
Go to step 3.
     
NO
     
     
     
Go to step 5.
3.
Open wire check (VCC2 line):

Open wire check (VCC2 line)
?1.
Measure the voltage between test points 1 and 2.
Test condition
Vehicle ON mode
 
Torque converter turbine speed sensor 3P connector: disconnected
Test point 1
Torque converter turbine speed sensor 3P connector No. 3
Test point 2
Body ground


Is there about 5 V?

     
YES
     
     
     
The VCC2 wire is OK. Go to step 4.
     
NO
     
     
     
Repair an open in the VCC2 wire between the torque converter turbine speed sensor and the TCM.?
4.
Torque converter turbine speed sensor check:

Torque converter turbine speed sensor check
?1.
Measure the voltage between test points 1 and 2.
Test condition
Vehicle ON mode
 
Torque converter turbine speed sensor 3P connector: disconnected
Test point 1
Torque converter turbine speed sensor 3P connector No. 1
Test point 2
Torque converter turbine speed sensor 3P connector No. 3


Is there about 5 V?

     
YES
     
     
     
     
NO
     
     
     
The torque converter turbine speed sensor is OK. Repair an open in the SG2 wire between the torque converter turbine speed sensor and the TCM.?
5.
Shorted wire check (NT line):

Shorted wire check (NT line)
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Disconnect the following connector.
TCM 50P connector

?3.
Check for continuity between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode
 
Torque converter turbine speed sensor 3P connector: disconnected
 
TCM 50P connector: disconnected
Test point 1
Torque converter turbine speed sensor 3P connector No. 2
Test point 2
Body ground


Is there continuity?

     
YES
     
     
     
Repair a short to ground in the NT wire between the torque converter turbine speed sensor and the TCM.?
     
NO
     
     
     
The NT wire is not shorted. Go to step 6.
6.
Open wire check (NT line):

Open wire check (NT line)
?1.
Check for continuity between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode
 
Torque converter turbine speed sensor 3P connector: disconnected
 
TCM 50P connector: disconnected
Test point 1
Torque converter turbine speed sensor 3P connector No. 2
Test point 2
TCM 50P connector No. 49


Is there continuity?

     
YES
     
     
     
The NT wire is OK. Check for any authorized service information related to the DTCs or symptoms you are troubleshooting, or substitute a known-good TCM, then recheck. If this DTC goes away and the TCM was substituted, replace the original TCM.?
     
NO
     
     
     
Repair an open in the NT wire between the torque converter turbine speed sensor and the TCM.?