Climate Control System Symptom Troubleshooting - The A/C compressor clutch does not engage, but the cooling fan operate, and the blower and heater controls work
The A/C compressor clutch does not engage, but the cooling fan operate, and the blower and heater controls work
NOTE:
It is normal for the A/C compressor to turn off under certain conditions, such as low idle, high engine coolant temperature, hard acceleration, or high/low refrigerant pressure.
Do not use this troubleshooting procedure if the cooling fan is also inoperative with the A/C on. Refer to the symptom troubleshooting index.
Before doing symptom troubleshooting, check for PGM-FI DTCs.
1.
PGM-FI system parameter check:

PGM-FI system parameter check
?1.
Connect the HDS to the DLC.

?2.
Start the engine.

?3.
Climate control panel without display: Set the A/C icon and the fan control icon, the fan control dial*1, or the fan control button*2 to ON.
Climate control panel with display: Set the A/C button and the fan control dial to ON.

*1: Without dual zone climate control
*2: With dual zone climate control

?4.
Check the parameter(s) below with the HDS.
Signal
Threshold
Current conditions
Values
Unit
Values
Unit
A/C SWITCH
ON
      
A/C CLUTCH
ON
      

Do the current condition(s) match the threshold?

     
YES
     
     
     
Go to step 2.
     
NO: A/C SWITCH is OFF
     
     
     
     
NO: A/C SWITCH is ON and A/C CLUTCH is OFF
     
     
     
A/C SWITCH is ON and A/C CLUTCH is OFF, check for any authorized service information related to the DTCs or symptoms you are troubleshooting, or substitute a known-good PCM, then recheck. If the symptom/indication goes away and the PCM was substituted, replace the original PCM.?
2.
Fuse check:

Fuse check
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Check the following fuse.
Fuse
No. A23

Is the fuse OK?

     
YES
     
     
     
Go to step 3.
     
NO
     
     
     
Replace the fuse, and recheck. If the fuse blows again, repair a short in the No. A23 fuse circuit.?
3.
A/C compressor clutch relay check:

A/C compressor clutch relay check
?1.
Remove the A/C compressor clutch relay from the under-hood fuse/relay box, and test it.

Is the relay OK?

     
YES
     
     
     
Go to step 4.
     
NO
     
     
     
Replace the A/C compressor clutch relay.?
4.
Open wire check (+B MG CLUTCH line):

Open wire check (+B MG CLUTCH line)
?1.
Measure the voltage between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode
A/C compressor clutch relay: disconnected
Test point 1
A/C compressor clutch relay 4P socket No. 1
Test point 2
Body ground


Is there battery voltage?

     
YES
     
     
     
The +B MG CLUTCH wire is OK. Go to step 5.
     
NO
     
     
     
Repair an open in the +B MG CLUTCH wire.?
5.
Determine possible failure area (A/C compressor clutch relay switch side circuit, A/C compressor clutch relay coil side circuit):

Determine possible failure area (A/C compressor clutch relay switch side circuit, A/C compressor clutch relay coil side circuit)
?1.
Connect terminals A and B with a jumper wire.
Terminal A
A/C compressor clutch relay 4P socket No. 1
Terminal B
A/C compressor clutch relay 4P socket No. 2


Does the A/C compressor clutch click?

     
YES
     
     
     
Go to step 6.
     
NO
     
     
     
Go to step 8.
6.
Open wire check (IG2 A/C (L15B7/K20C2 engine) or IG2 OPTION (L15BA/L15BY engine) line):

Open wire check (IG2 A/C (L15B7/K20C2 engine) or IG2 OPTION (L15BA/L15BY engine) line)
?1.
Disconnect the jumper wire.

?2.
Turn the vehicle to the ON mode.

?3.
Measure the voltage between test points 1 and 2.
Test condition
Vehicle ON mode
A/C compressor clutch relay: disconnected
Test point 1
A/C compressor clutch relay 4P socket No. 3
Test point 2
Body ground


Is there battery voltage?

     
YES
     
     
     
The IG2 A/C (L15B7/K20C2 engine) or the IG2 OPTION (L15BA/L15BY engine) wire is OK. Go to step 7.
     
NO: L15B7/K20C2 engine
     
     
     
Repair an open in the IG2 A/C wire.?
     
NO: L15BA/L15BY engine
     
     
     
Repair an open in the IG2 OPTION wire.?
7.
Open wire check (A/C MG CLUTCH RLY CL-/ACC line):

Open wire check (A/C MG CLUTCH RLY CL-/ACC line)
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Reinstall the A/C compressor clutch relay.

?3.
Jump the SCS line with the HDS, and wait more than 1 minute.

NOTE: This step must be done to protect the PCM from damage.

?4.
Disconnect the following connector.
PCM connector E (80P)

?5.
Connect terminals A and B with a jumper wire.
Terminal A
PCM connector E (80P) No. 31
Terminal B
Body ground

?6.
Turn the vehicle to the ON mode.

Does the A/C compressor clutch click?

     
YES
     
     
     
Check for any authorized service information related to the DTCs or symptoms you are troubleshooting, or substitute a known-good PCM, then recheck. If the symptom/indication goes away and the PCM was substituted, replace the original PCM.?
     
NO
     
     
     
Repair an open in the A/C MG CLUTCH RLY CL-/ACC wire.?
8.
Open wire check (A/C MG CLUTCH/MG CLUTCH (except K20C2 engine) or A/C MG CLUTCH/AC MG CLUTCH (K20C2 engine) line):

Open wire check (A/C MG CLUTCH/MG CLUTCH (except K20C2 engine) or A/C MG CLUTCH/AC MG CLUTCH (K20C2 engine) line)
?1.
Disconnect the jumper wire.

?2.
Disconnect the following connector.
A/C compressor 3P connector

?3.
Check for continuity between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode
A/C compressor clutch relay: disconnected
A/C compressor 3P connector: disconnected
Test point 1
A/C compressor clutch relay 4P socket No. 2
Test point 2
A/C compressor 3P connector No. 1


Is there continuity?

     
YES
     
     
     
The A/C MG CLUTCH/MG CLUTCH (except K20C2 engine) or the A/C MG CLUTCH/AC MG CLUTCH (K20C2 engine) wire is OK. Check the A/C compressor clutch clearance and the A/C compressor clutch field coil. Repair as needed.?
     
NO: Except K20C2 engine
     
     
     
Repair an open in the A/C MG CLUTCH/MG CLUTCH wire.?
     
NO: K20C2 engine
     
     
     
Repair an open in the A/C MG CLUTCH/AC MG CLUTCH wire.?