|
DTC Advanced Diagnostics: SRS related DTCs
SRS Related DTCs
NOTE
|
Always check "How to troubleshoot the SRS system" and proceed along each "DTC Troubleshooting" procedure. |
|
Make sure the 12 volt battery is fully charged. If not, the results of tests may not be accurate. |
|
The SRS indicator will turn on when the 12 volt battery voltage becomes below 10 volts. |
|
The possible causes shown may not be a complete list of all potential problems, and it is possible that there may be other causes. |
DTC B0001-11: Short to Ground in the Driver's Airbag First Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to ground between the SRS unit and the driver's airbag first inflator (LA1+, LA1- lines) |
|
Driver's airbag internal failure (Driver's airbag first inflator) |
|
SRS unit internal failure | | |
|
DTC B0001-12: Short to Power in the Driver's Airbag First Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to power between the SRS unit and the driver's airbag first inflator (LA1+, LA1- lines) |
|
Driver's airbag internal failure (Driver's airbag first inflator) |
|
SRS unit internal failure | | |
|
DTC B0001-13: Open or Increased Resistance in the Driver's Airbag First Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open or Poor connection between the SRS unit and the driver's airbag first inflator (LA1+, LA1- lines) |
|
Driver's airbag internal failure (Driver's airbag first inflator) |
|
SRS unit internal failure | | |
|
DTC B0001-1A: Decreased Resistance in the Driver's Airbag First Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to another line or Poor connection between the SRS unit and the driver's airbag first inflator (LA1+, LA1- lines) |
|
Driver's airbag internal failure (Driver's airbag first inflator) |
|
SRS unit internal failure | | |
|
DTC B0002-11: Short to Ground in the Driver's Airbag Second Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to ground between the SRS unit and the driver's airbag second inflator (LA2+, LA2- lines) |
|
Driver's airbag internal failure (Driver's airbag second inflator) |
|
SRS unit internal failure | | |
|
DTC B0002-12: Short to Power in the Driver's Airbag Second Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to power between the SRS unit and the driver's airbag second inflator (LA2+, LA2- lines) |
|
Driver's airbag internal failure (Driver's airbag second inflator) |
|
SRS unit internal failure | | |
|
DTC B0002-13: Open or Increased Resistance in the Driver's Airbag Second Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open or Poor connection between the SRS unit and the driver's airbag second inflator (LA2+, LA2- lines) |
|
Driver's airbag internal failure (Driver's airbag second inflator) |
|
SRS unit internal failure | | |
|
DTC B0002-1A: Decreased Resistance in the Driver's Airbag Second Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to another line or Poor connection between the SRS unit and the driver's airbag second inflator (LA2+, LA2- lines) |
|
Driver's airbag internal failure (Driver's airbag second inflator) |
|
SRS unit internal failure | | |
|
DTC B0010-11: Short to Ground in the Front Passenger's Airbag First Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to ground between the SRS unit and the front passenger's airbag first inflator (RA1+, RA1- lines) |
|
Front passenger's airbag internal failure (Front passenger's airbag first inflator) |
|
SRS unit internal failure | | |
|
DTC B0010-12: Short to Power in the Front Passenger's Airbag First Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to power between the SRS unit and the front passenger's airbag first inflator (RA1+, RA1- lines) |
|
SRS unit internal failure | | |
|
DTC B0010-13: Open or Increased Resistance in the Front Passenger's Airbag First Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open or Poor connection between the SRS unit and the front passenger's airbag first inflator (RA1+, RA1- lines) |
|
Front passenger's airbag internal failure (Front passenger's airbag first inflator) |
|
SRS unit internal failure | | |
|
DTC B0010-1A: Decreased Resistance in the Front Passenger's Airbag First Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to another line or Poor connection between the SRS unit and the front passenger's airbag first inflator (RA1+, RA1- lines) |
|
Front passenger's airbag internal failure (Front passenger's airbag first inflator) |
|
SRS unit internal failure | | |
|
DTC B0011-11: Short to Ground in the Front Passenger's Airbag Second Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to ground between the SRS unit and the front passenger's airbag second inflator (RA2+, RA2- lines) |
|
Front passenger's airbag internal failure (Front passenger's airbag second inflator) |
|
SRS unit internal failure | | |
|
DTC B0011-12: Short to Power in the Front Passenger's Airbag Second Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to power between the SRS unit and the front passenger's airbag second inflator (RA2+, RA2- lines) |
|
SRS unit internal failure | | |
|
DTC B0011-13: Open or Increased Resistance in the Front Passenger's Airbag Second Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open or Poor connection between the SRS unit and the front passenger's airbag second inflator (RA2+, RA2- lines) |
|
Front passenger's airbag internal failure (Front passenger's airbag second inflator) |
|
SRS unit internal failure | | |
|
DTC B0011-1A: Decreased Resistance in the Front Passenger's Airbag Second Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to another line or Poor connection between the SRS unit and the front passenger's airbag second inflator (RA2+, RA2- lines) |
|
Front passenger's airbag internal failure (Front passenger's airbag second inflator) |
|
SRS unit internal failure | | |
|
DTC B0020-11: Short to Ground in the Driver's Side Airbag Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to ground between the SRS unit and the driver's side airbag inflator (LSA+, LSA- lines) |
|
Driver's side airbag internal failure (Driver's side airbag inflator) |
|
SRS unit internal failure | | |
|
DTC B0020-12: Short to Power in the Driver's Side Airbag Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to power between the SRS unit and the driver's side airbag inflator (LSA+, LSA- lines) |
|
SRS unit internal failure | | |
|
DTC B0020-13: Open or Increased Resistance in the Driver's Side Airbag Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open or Poor connection between the SRS unit and the driver's side airbag inflator (LSA+, LSA- lines) |
|
Driver's side airbag internal failure (Driver's side airbag inflator) |
|
SRS unit internal failure | | |
|
DTC B0020-1A: Decreased Resistance in the Driver's Side Airbag Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to another line or Poor connection between the SRS unit and the driver's side airbag inflator (LSA+, LSA- lines) |
|
Driver's side airbag internal failure (Driver's side airbag inflator) |
|
SRS unit internal failure | | |
|
DTC B0021-11: Short to Ground in the Left Side Curtain Airbag First Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to ground between the SRS unit and the left side curtain airbag inflator (LCA+, LCA- lines) |
|
Left side curtain airbag internal failure (Left side curtain airbag inflator) |
|
SRS unit internal failure | | |
|
DTC B0021-12: Short to Power in the Left Side Curtain Airbag First Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to power between the SRS unit and the left side curtain airbag inflator (LCA+, LCA- lines) |
|
SRS unit internal failure | | |
|
DTC B0021-13: Open or Increased Resistance in the Left Side Curtain Airbag First Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open or Poor connection between the SRS unit and the left side curtain airbag inflator (LCA+, LCA- lines) |
|
Left side curtain airbag internal failure (Left side curtain airbag inflator) |
|
SRS unit internal failure | | |
|
DTC B0021-1A: Decreased Resistance in the Left Side Curtain Airbag First Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to another line or Poor connection between the SRS unit and the left side curtain airbag inflator (LCA+, LCA- lines) |
|
Left side curtain airbag internal failure (Left side curtain airbag inflator) |
|
SRS unit internal failure | | |
|
DTC B0028-11: Short to Ground in the Front Passenger's Side Airbag Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to ground between the SRS unit and the front passenger's side airbag inflator (RSA+, RSA- lines) |
|
Front passenger's side airbag internal failure (Front passenger's side airbag inflator) |
|
SRS unit internal failure | | |
|
DTC B0028-12: Short to Power in the Front Passenger's Side Airbag Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to power between the SRS unit and the front passenger's side airbag inflator (RSA+, RSA- lines) |
|
SRS unit internal failure | | |
|
DTC B0028-13: Open or Increased Resistance in the Front Passenger's Side Airbag Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open or Poor connection between the SRS unit and the front passenger's side airbag inflator (RSA+, RSA- lines) |
|
Front passenger's side airbag internal failure (Front passenger's side airbag inflator) |
|
SRS unit internal failure | | |
|
DTC B0028-1A: Decreased Resistance in the Front Passenger's Side Airbag Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to another line or Poor connection between the SRS unit and the front passenger's side airbag inflator (RSA+, RSA- lines) |
|
Front passenger's side airbag internal failure (Front passenger's side airbag inflator) |
|
SRS unit internal failure | | |
|
DTC B0029-11: Short to Ground in the Right Side Curtain Airbag First Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to ground between the SRS unit and the right side curtain airbag inflator (RCA+, RCA- lines) |
|
Right side curtain airbag internal failure (Right side curtain airbag inflator) |
|
SRS unit internal failure | | |
|
DTC B0029-12: Short to Power in the Right Side Curtain Airbag First Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to power between the SRS unit and the right side curtain airbag inflator (RCA+, RCA- lines) |
|
SRS unit internal failure | | |
|
DTC B0029-13: Open or Increased Resistance in the Right Side Curtain Airbag First Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open or Poor connection between the SRS unit and the right side curtain airbag inflator (RCA+, RCA- lines) |
|
Right side curtain airbag internal failure (Right side curtain airbag inflator) |
|
SRS unit internal failure | | |
|
DTC B0029-1A: Decreased Resistance in the Right Side Curtain Airbag First Inflator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to another line or Poor connection between the SRS unit and the right side curtain airbag inflator (RCA+, RCA- lines) |
|
Right side curtain airbag internal failure (Right side curtain airbag inflator) |
|
SRS unit internal failure | | |
|
DTC B0050-11: Short or Decreased Resistance in the Driver's Seat Belt Buckle Switch
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to ground or Short to power between the SRS unit and the driver's seat belt buckle switch (FLBC line) |
|
Driver's seat belt buckle assembly internal failure (Driver's seat belt buckle switch) |
|
SRS unit internal failure | | |
|
DTC B0050-13: Open or Increased Resistance in the Driver's Seat Belt Buckle Switch
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open or Poor connection between the SRS unit and the driver's seat belt buckle switch (FLBC line) |
|
Open or Poor connection between the driver's seat belt buckle switch and the body ground (GND line) |
|
Driver's seat belt buckle assembly internal failure (Driver's seat belt buckle switch) |
|
SRS unit internal failure | | |
|
DTC B0052-11: Short or Decreased Resistance in the Front Passenger's Seat Belt Buckle Switch
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to ground or Short to power between the SRS unit and the front passenger's seat belt buckle switch (FRBC line) |
|
Front passenger's seat belt buckle assembly internal failure (Front passenger's seat belt buckle switch) |
|
SRS unit internal failure | | |
|
DTC B0052-13: Open or Increased Resistance in the Front Passenger's Seat Belt Buckle Switch
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open or Poor connection between the SRS unit and the front passenger's seat belt buckle switch (FRBC line) |
|
Open or Poor connection between the front passenger's seat belt buckle switch and the body ground (GND line) |
|
Front passenger's seat belt buckle assembly internal failure (Front passenger's seat belt buckle switch) |
|
SRS unit internal failure | | |
|
DTC B0070-11: Short to Ground in the Driver's Seat Belt Tensioner
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to ground between the SRS unit and the driver's seat belt tensioner (LRP+, LRP- lines) |
|
Driver's seat belt internal failure (Driver's seat belt tensioner) |
|
SRS unit internal failure | | |
|
DTC B0070-12: Short to Power in the Driver's Seat Belt Tensioner
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to power between the SRS unit and the driver's seat belt tensioner (LRP+, LRP- lines) |
|
SRS unit internal failure | | |
|
DTC B0070-13: Open or Increased Resistance in the Driver's Seat Belt Tensioner
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open or Poor connection between the SRS unit and the driver's seat belt tensioner (LRP+, LRP- lines) |
|
Driver's seat belt internal failure (Driver's seat belt tensioner) |
|
SRS unit internal failure | | |
|
DTC B0070-1A: Decreased Resistance in the Driver's Seat Belt Tensioner
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to another line or Poor connection between the SRS unit and the driver's seat belt tensioner (LRP+, LRP- lines) |
|
Driver's seat belt internal failure (Driver's seat belt tensioner) |
|
SRS unit internal failure | | |
|
DTC B0072-11: Short to Ground in the Front Passenger's Seat Belt Tensioner
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to ground between the SRS unit and the front passenger's seat belt tensioner (RRP+, RRP- lines) |
|
Front passenger's seat belt internal failure (Front passenger's seat belt tensioner) |
|
SRS unit internal failure | | |
|
DTC B0072-12: Short to Power in the Front Passenger's Seat Belt Tensioner
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to power between the SRS unit and the front passenger's seat belt tensioner (RRP+, RRP- lines) |
|
SRS unit internal failure | | |
|
DTC B0072-13: Open or Increased Resistance in the Front Passenger's Seat Belt Tensioner
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open or Poor connection between the SRS unit and the front passenger's seat belt tensioner (RRP+, RRP- lines) |
|
Front passenger's seat belt internal failure (Front passenger's seat belt tensioner) |
|
SRS unit internal failure | | |
|
DTC B0072-1A: Decreased Resistance in the Front Passenger's Seat Belt Tensioner
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to another line or Poor connection between the SRS unit and the front passenger's seat belt tensioner (RRP+, RRP- lines) |
|
Front passenger's seat belt internal failure (Front passenger's seat belt tensioner) |
|
SRS unit internal failure | | |
|
DTC B0079-11: Short to Ground in the Driver's Seat Belt Outer Lap Tensioner
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to ground between the SRS unit and the driver's seat belt outer lap tensioner (LLP+, LLP- lines) |
|
Driver's seat belt internal failure (Driver's seat belt outer lap tensioner) |
|
SRS unit internal failure | | |
|
DTC B0079-12: Short to Power in the Driver's Seat Belt Outer Lap Tensioner
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to power between the SRS unit and the driver's seat belt outer lap tensioner (LLP+, LLP- lines) |
|
Driver's seat belt internal failure (Driver's seat belt outer lap tensioner) |
|
SRS unit internal failure | | |
|
DTC B0079-13: Open or Increased Resistance in the Driver's Seat Belt Outer Lap Tensioner
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open or Poor connection between the SRS unit and the driver's seat belt outer lap tensioner (LLP+, LLP- lines) |
|
Driver's seat belt internal failure (Driver's seat belt outer lap tensioner) |
|
SRS unit internal failure | | |
|
DTC B0079-1A: Decreased Resistance in the Driver's Seat Belt Outer Lap Tensioner
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to another line or Poor connection between the SRS unit and the driver's seat belt outer lap tensioner (LLP+, LLP- lines) |
|
Driver's seat belt internal failure (Driver's seat belt outer lap tensioner) |
|
SRS unit internal failure | | |
|
DTC B0082-11: Short to Ground in the Selectable Energy Absorption Device of the Front Passenger's Seat Belt Tensioner
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to ground between the SRS unit and the selectable energy absorption device (READ+, READ- lines) |
|
Front passenger's seat belt internal failure (Selectable energy absorption device) |
|
SRS unit internal failure | | |
|
DTC B0082-12: Short to Power in the Selectable Energy Absorption Device of the Front Passenger's Seat Belt Tensioner
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to power between the SRS unit and the selectable energy absorption device (READ+, READ- lines) |
|
Front passenger's seat belt internal failure (Selectable energy absorption device) |
|
SRS unit internal failure | | |
|
DTC B0082-13: Open or Increased Resistance in the Selectable Energy Absorption Device of the Front Passenger's Seat Belt Tensioner
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open or Poor connection between the SRS unit and the selectable energy absorption device (READ+, READ- lines) |
|
Front passenger's seat belt internal failure (Selectable energy absorption device) |
|
SRS unit internal failure | | |
|
DTC B0082-1A: Decreased Resistance in the Selectable Energy Absorption Device of the Front Passenger's Seat Belt Tensioner
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to another line or Poor connection between the SRS unit and the selectable energy absorption device (READ+, READ- lines) |
|
Front passenger's seat belt internal failure (Selectable energy absorption device) |
|
SRS unit internal failure | | |
|
DTC B0090-4A: Internal Failure of the Left Front Impact Sensor
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Incorrect impact sensor installed |
|
Incorrect SRS unit installed |
|
Left front impact sensor internal failure |
|
SRS unit internal failure | | |
|
DTC B0090-87: No Signal From the Left Front Impact Sensor
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the left front impact sensor (LFS+, LFS- lines) |
|
Left front impact sensor internal failure |
|
SRS unit internal failure | | |
|
DTC B0090-92: Internal Failure of the Left Front Impact Sensor
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Left front impact sensor internal failure |
|
SRS unit internal failure | | |
|
DTC B0091-4A: Internal Failure of the Left Side Impact Sensor (first)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Incorrect impact sensor installed |
|
Incorrect SRS unit installed |
|
Left side impact sensor (first) internal failure |
|
SRS unit internal failure | | |
|
DTC B0091-87: No Signal From the Left Side Impact Sensor (first)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the left side impact sensor (first) (LS1+, LS1- lines) |
|
Left side impact sensor (first) internal failure |
|
SRS unit internal failure | | |
|
DTC B0091-92: Internal Failure of the Left Side Impact Sensor (first)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Left side impact sensor (first) internal failure |
|
SRS unit internal failure | | |
|
DTC B0092-4A: Internal Failure of the Left Side Impact Sensor (second)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Incorrect impact sensor installed |
|
Incorrect SRS unit installed |
|
Left side impact sensor (second) internal failure |
|
SRS unit internal failure | | |
|
DTC B0092-87: No Signal From the Left Side Impact Sensor (second)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the left side impact sensor (second) (LS2+, LS2- lines) |
|
Left side impact sensor (second) internal failure |
|
SRS unit internal failure | | |
|
DTC B0092-92: Internal Failure of the Left Side Impact Sensor (second)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Left side impact sensor (second) internal failure |
|
SRS unit internal failure | | |
|
DTC B0095-4A: Internal Failure of the Right Front Impact Sensor
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Incorrect impact sensor installed |
|
Incorrect SRS unit installed |
|
Right front impact sensor internal failure |
|
SRS unit internal failure | | |
|
DTC B0095-87: No Signal From the Right Front Impact Sensor
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the right front impact sensor (RFS+, RFS- lines) |
|
Right front impact sensor internal failure |
|
SRS unit internal failure | | |
|
DTC B0095-92: Internal Failure of the Right Front Impact Sensor
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Right front impact sensor internal failure |
|
SRS unit internal failure | | |
|
DTC B0096-4A: Internal Failure of the Right Side Impact Sensor (first)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Incorrect impact sensor installed |
|
Incorrect SRS unit installed |
|
Right side impact sensor (first) internal failure |
|
SRS unit internal failure | | |
|
DTC B0096-87: No Signal From the Right Side Impact Sensor (first)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the right side impact sensor (first) (RS1+, RS1- lines) |
|
Right side impact sensor (first) internal failure |
|
SRS unit internal failure | | |
|
DTC B0096-92: Internal Failure of the Right Side Impact Sensor (first)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Right side impact sensor (first) internal failure |
|
SRS unit internal failure | | |
|
DTC B0097-4A: Internal Failure of the Right Side Impact Sensor (second)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Incorrect impact sensor installed |
|
Incorrect SRS unit installed |
|
Right side impact sensor (second) internal failure |
|
SRS unit internal failure | | |
|
DTC B0097-87: No Signal From the Right Side Impact Sensor (second)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the right side impact sensor (second) (RS2+, RS2- lines) |
|
Right side impact sensor (second) internal failure |
|
SRS unit internal failure | | |
|
DTC B0097-92: Internal Failure of the Right Side Impact Sensor (second)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Right side impact sensor (second) internal failure |
|
SRS unit internal failure | | |
|
DTC B00A0-54: Front Passenger's Weight Sensor not Calibrated
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Front passenger's weight sensor not initialized | | |
|
DTC B00B5-11: Short or Decreased Resistance in the Driver's Seat Position Sensor
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to ground between the SRS unit and the driver's seat position sensor (SS+ line) |
|
Driver's seat position sensor internal failure |
|
SRS unit internal failure | | |
|
DTC B00B5-13: Open or Increased Resistance in the Driver's Seat Position Sensor
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open or Poor connection between the SRS unit and the driver's seat position sensor (SS+ line) |
|
Open or Poor connection between the driver's seat position sensor and the body ground (GND line) |
|
Driver's seat position sensor internal failure |
|
SRS unit internal failure | | |
|
DTC B00C0-16: Internal Failure of the Front Passenger's Weight Sensor (front inner side)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Front passenger's weight sensor internal failure (front inner side) | | |
|
DTC B00C0-4A: Different Supplier ID/Function ID of the Front Passenger's Weight Sensor (front inner side)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Front passenger's weight sensor internal failure (front inner side) |
|
SRS unit internal failure | | |
|
DTC B00C0-54: Different Serial ID of the Front Passenger's Weight Sensor (front inner side)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
SRS unit internal failure | | |
|
DTC B00C0-87: No Signal From the Front Passenger's Weight Sensor (front inner side)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open or Poor connection between the SRS unit and the front passenger's weight sensor (front inner side) (SWSP1/SWS+, SWS1G/SWS-, SWS1/SWSS lines) |
|
Short to power or Short to ground between the SRS unit and the front passenger's weight sensor (front inner side) (SWS1/SWSS line) |
|
Short to another line or Poor connection between the SRS unit and the front passenger's weight sensor (front inner side) (SWS1/SWSS line to SWS1G/SWS- line, SWS1/SWSS line to SWSP1/SWS+ line) |
|
SRS unit internal failure |
|
Front passenger's weight sensor internal failure (front inner side) | | |
|
DTC B00C0-96: Internal Failure of the Front Passenger's Weight Sensor (front inner side)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Front passenger's weight sensor internal failure (front inner side) | | |
|
DTC B00C1-16: Internal Failure of the Front Passenger's Weight Sensor (front outer side)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Front passenger's weight sensor internal failure (front outer side) | | |
|
DTC B00C1-4A: Different Supplier ID/Function ID of the Front Passenger's Weight Sensor (front outer side)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Front passenger's weight sensor internal failure (front outer side) |
|
SRS unit internal failure | | |
|
DTC B00C1-54: Different Serial ID of the Front Passenger's Weight Sensor (front outer side)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
SRS unit internal failure | | |
|
DTC B00C1-87: No Signal From the Front Passenger's Weight Sensor (front outer side)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open or Poor connection between the SRS unit and the front passenger's weight sensor (front inner side) (SWSP3/SWS+, SWS3G/SWS-, SWS3/SWSS lines) |
|
SRS unit internal failure |
|
Front passenger's weight sensor internal failure (front outer side) | | |
|
DTC B00C1-96: Internal Failure of the Front Passenger's Weight Sensor (front outer side)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Front passenger's weight sensor internal failure (front outer side) | | |
|
DTC B00C2-16: Internal Failure of the Front Passenger's Weight Sensor (rear inner side)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Front passenger's weight sensor internal failure (rear inner side) | | |
|
DTC B00C2-4A: Different Supplier ID/Function ID of the Front Passenger's Weight Sensor (rear inner side)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Front passenger's weight sensor internal failure (rear inner side) |
|
SRS unit internal failure | | |
|
DTC B00C2-54: Different Serial ID of the Front Passenger's Weight Sensor (rear inner side)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
SRS unit internal failure | | |
|
DTC B00C2-87: No Signal From the Front Passenger's Weight Sensor (rear inner side)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open or Poor connection between the SRS unit and the front passenger's weight sensor (rear inner side) (SWSP2/SWS+, SWS2G/SWS-, SWS2/SWSS lines) |
|
Front passenger's weight sensor internal failure (rear inner side) |
|
SRS unit internal failure | | |
|
DTC B00C2-96: Internal Failure of the Front Passenger's Weight Sensor (rear inner side)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Front passenger's weight sensor internal failure (rear inner side) | | |
|
DTC B00C3-16: Internal Failure of the Front Passenger's Weight Sensor (rear outer side)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Front passenger's weight sensor internal failure (rear outer side) | | |
|
DTC B00C3-4A: Different Supplier ID/Function ID of the Front Passenger's Weight Sensor (rear outer side)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Front passenger's weight sensor internal failure (rear outer side) |
|
SRS unit internal failure | | |
|
DTC B00C3-54: Different Serial ID of the Front Passenger's Weight Sensor (rear outer side)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
SRS unit internal failure | | |
|
DTC B00C3-87: No Signal From the Front Passenger's Weight Sensor (rear outer side)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open or Poor connection between the SRS unit and the front passenger's weight sensor (rear outer side) (SWSP4/SWS+, SWS4G/SWS-, SWS4/SWSS lines) |
|
Front passenger's weight sensor internal failure (rear outer side) |
|
SRS unit internal failure | | |
|
DTC B00C3-96: Internal Failure of the Front Passenger's Weight Sensor (rear outer side)
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Front passenger's weight sensor internal failure (rear outer side) | | |
|
DTC B00D5-14: Open or Short to Ground in the Front Passenger's Airbag Cutoff Indicator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 9 seconds. | |
Duration |
About 9 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Open or Short to ground between the SRS unit and the front passenger's airbag cutoff indicator (OFF PTT line) |
|
Open or Short to ground between the 12 volt battery and the front passenger's airbag cutoff indicator |
|
Front passenger's airbag cutoff indicator internal failure |
|
SRS unit internal failure | | |
|
DTC B00D5-17: Short to Power in the Front Passenger's Airbag Cutoff Indicator
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 9 seconds. | |
Duration |
About 9 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to power between the SRS unit and the front passenger's airbag cutoff indicator (OFF PTT line) |
|
Front passenger's airbag cutoff indicator internal failure |
|
SRS unit internal failure | | |
|
DTC B2800-49: Internal Failure of the SRS Unit
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
SRS unit internal failure | | |
|
DTC B2801-49: Internal Failure of the SRS Unit
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
SRS unit internal failure | | |
|
DTC B2802-49: Internal Failure of the SRS Unit
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
SRS unit internal failure | | |
|
DTC B2840-13: SRS Unit Connector A Not Properly Installed
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Poor connection between the SRS unit and connector A |
|
SRS unit internal failure | | |
|
DTC B2841-13: SRS Unit Connector B Not Properly Installed
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Poor connection between the SRS unit and connector B |
|
SRS unit internal failure | | |
|
DTC U3000-49: Internal Failure of the SRS Unit
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
Short to power or Short to ground between the SRS unit and the front passenger's weight sensor (front inner side) (SWSP1 line) |
|
Short to another line between the SRS unit and the front passenger's weight sensor (front inner side) (SWSP1 line to SWS1G line) |
|
Short to power or Short to ground between the SRS unit and the front passenger's weight sensor (rear inner side) (SWSP2 line) |
|
Short to another line between the SRS unit and the front passenger's weight sensor (rear inner side) (SWSP2 line to SWS2G line) |
|
Short to power or Short to ground between the SRS unit and the front passenger's weight sensor (front outer side) (SWSP3 line) |
|
Short to another line between the SRS unit and the front passenger's weight sensor (front outer side) (SWSP3 line to SWS3G line) |
|
Short to power or Short to ground between the SRS unit and the front passenger's weight sensor (rear outer side) (SWSP4 line) |
|
Short to another line between the SRS unit and the front passenger's weight sensor (rear outer side) (SWSP4 line to SWS4G line) |
|
SRS unit internal failure |
|
Front passenger's weight sensor Internal failure | | |
|
DTC U3000-51: SRS Unit Programming Error
Confirmation Procedure |
Basic Condition:
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
Duration |
About 6 seconds |
DTC Type |
|
1 drive cycle |
|
SRS indicator on | |
Fail Safe Action |
|
Possible Cause |
|
SRS unit internal failure | | |
| |