|
Fuel Line/Quick-Connect Fitting Precautions
The fuel line/quick-connect fittings (A to J) connect following:
|
|
A: fuel feed hose (K) to fuel feed pipe (high pressure fuel pump) (L) |
|
|
B: fuel feed hose (K) to fuel feed line (M) |
|
|
C: fuel tank unit (N) to suction line (O) |
|
|
D: fuel tank unit (N) to fuel vent line (P) |
|
|
E: fuel tank unit (N) to fuel feed line (M) |
|
|
F: EVAP canister (Q) to fuel vapor line (R) |
|
|
G: breather line (S) to suction line (O) |
|
|
H: breather line (S) to fuel filler pipe (T) |
|
|
I: one way valve tube (U) to fuel fill pipe (T) |
|
|
J: one way valve tube (U) to fuel fill pipe (T) |
When removing or installing the fuel feed hose, fuel tank unit, fuel tank, EVAP canister, or when disconnecting/connecting the quick-connect fittings, pay attention to the following:
|
|
The fuel feed hose, the fuel line, and the quick-connect fittings are not heat-resistant; be careful not to damage them during welding or other heat-generating procedures. |
|
|
The fuel feed hose, the fuel line, and the quick-connect fittings are not acid-proof; do not touch them with a shop towel which was used for wiping 12 volt battery electrolyte. Replace them if they came into contact with 12 volt battery electrolyte or something similar. |
|
|
When connecting or disconnecting the fuel feed hose, the fuel line, and the quick-connect fittings, be careful not to bend or twist them excessively. Replace them if they are damaged. |
A disconnected quick-connect fitting can be reconnected, but the retainer on the mating line cannot be reused once it has been removed from the line. Replace the retainer when:
|
|
Replacing the fuel feed pipe (high pressure fuel pump) |
|
|
Replacing the fuel line |
|
|
Replacing the fuel pump |
|
|
Replacing the EVAP canister |
|
|
Replacing the fuel filter |
|
|
Replacing the fuel tank |
|
|
Replacing the fuel fill pipe |
|
|
The retainer has been removed from the pipe |
|
|
The retainer is damaged |
Use the same manufacturer retainer and the same size retainer when the replacing the retainer.
|
Location |
Manufacturer |
Retainer color |
Piping diameter |
|
A*1 |
Tokai/
Sumitomo Riko |
Green |
6.3 mm
(0.248 in) |
|
A*2 |
Tokai/
Sumitomo Riko |
Blue green |
8.0 mm
(0.315 in) |
|
B |
Tokai/
Sumitomo Riko |
Green |
6.3 mm
(0.248 in) |
|
C |
Tokai/
Sumitomo Riko |
Blue green |
8.0 mm
(0.315 in) |
|
D |
Tokai/
Sumitomo Riko |
Blue green |
8.0 mm
(0.315 in) |
|
E |
Sanoh |
White |
9.5 mm
(0.374 in) |
|
F |
Sanoh |
White |
11.8 mm
(0.465 in) |
|
G |
Yachiyo |
Blue |
11.8 mm
(0.465 in) |
|
H |
Tokai/
Sumitomo Riko |
Natural |
11.8 mm
(0.465 in) |
|
I |
Tokai/
Sumitomo Riko |
Natural |
11.8 mm
(0.465 in) |
|
J |
Tokai/
Sumitomo Riko |
Natural |
11.8 mm
(0.465 in) | |
|
| | 