DTC Troubleshooting: P0098
DTC P0098: IAT Sensor 2 Circuit High Voltage
NOTE: Before you troubleshoot, review the general troubleshooting information.

DTC Description
Confirmed DTC
Pending DTC
Freeze Frame
P0098 IAT Sensor 2 Circuit High Voltage
      

1.
Problem verification:

Problem verification
?1.
Turn the vehicle to the ON mode.

?2.
Check the parameter(s) below with the HDS.
Signal
Threshold
Current conditions
Values
Unit
Values
Unit
IAT SENSOR 2
More than 4.92
V
    

Do the current condition(s) match the threshold?

     
YES
     
     
     
The failure is duplicated. Go to step 2.
     
NO
     
     
     
Intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at IAT sensor 2 and the PCM. If the freeze data/on-board snapshot of this DTC is recorded, try to reproduce the failure under the same conditions with the freeze data/on-board snapshot.?
2.
Determine possible failure area (IAT sensor 2, others):

Determine possible failure area (IAT sensor 2, others)
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Disconnect the following connector.
IAT sensor 2 2P connector

?3.
Connect terminals A and B with a jumper wire.
Terminal A
IAT sensor 2 2P connector No. 1
Terminal B
IAT sensor 2 2P connector No. 2


?4.
Turn the vehicle to the ON mode.

?5.
Check the parameter(s) below with the HDS.
Signal
Threshold
Current conditions
Values
Unit
Values
Unit
IAT SENSOR 2
More than 4.92
V
    

Do the current condition(s) match the threshold?

     
YES
     
     
     
Go to step 3.
     
NO
     
     
     
3.
Determine possible failure area (INTA line, others):

Determine possible failure area (INTA line, others)
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Remove the jumper wire.

?3.
Turn the vehicle to the ON mode.

?4.
Measure the voltage between test points 1 and 2.
Test condition
Vehicle ON mode
 
IAT sensor 2 2P connector: disconnected
Test point 1
IAT sensor 2 2P connector No. 1
Test point 2
Body ground


Is there about 5.0 V?

     
YES
     
     
     
Go to step 4.
     
NO
     
     
     
Go to step 5.
4.
Open wire check (SG2 line):

Open wire check (SG2 line)
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Jump the SCS line with the HDS.


?3.
Disconnect the following connector.
PCM connector C (51P)

?4.
Check for continuity between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode
 
IAT sensor 2 2P connector: disconnected
 
PCM connector C (51P): disconnected
Test point 1
IAT sensor 2 2P connector No. 2
Test point 2
PCM connector C (51P) No. 31


Is there continuity?

     
YES
     
     
     
The SG2 wire is OK. Update the PCM if it does not have the latest software, or substitute a known-good PCM, then recheck. If DTC P0098 goes away and the PCM was updated, troubleshooting is complete. If DTC P0098 goes away and the PCM was substituted, replace the original PCM.?
     
NO
     
     
     
Repair an open in the SG2 wire between IAT sensor 2 and the PCM (C31).?
5.
Open wire check (INTA line):

Open wire check (INTA line)
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Jump the SCS line with the HDS.


?3.
Disconnect the following connector.
PCM connector B (51P)

?4.
Check for continuity between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode
 
IAT sensor 2 2P connector: disconnected
 
PCM connector B (51P): disconnected
Test point 1
IAT sensor 2 2P connector No. 1
Test point 2
PCM connector B (51P) No. 42


Is there continuity?

     
YES
     
     
     
The INTA wire is OK. Update the PCM if it does not have the latest software, or substitute a known-good PCM, then recheck. If DTC P0098 goes away and the PCM was updated, troubleshooting is complete. If DTC P0098 goes away and the PCM was substituted, replace the original PCM.?
     
NO
     
     
     
Repair an open in the INTA wire between IAT sensor 2 and the PCM (B42).?