DTC Troubleshooting: P0833-12

DTC P0833-12: Clutch Pedal Position Switch B Stuck ON

NOTE:

	Before you troubleshoot, review the general troubleshooting information.
	If DTC U0029-00 is indicated at the same time, do the DTC U0029-00 troubleshooting first.

DTC Description	DTC	Freeze Frame
P0833-12 Clutch Pedal Position Switch B Stuck ON

PGM-FI DTCs check:

PGM-FI DTCs check

?1.	Turn the vehicle to the ON mode.

?2.

Check for PGM-FI DTCs with the HDS.

DTC Description	Confirmed DTC	Pending DTC	Freeze Frame

Are any DTCs indicated?


	YES

Go to indicated DTC's troubleshooting.?


	NO

Go to step 2.

PGM-FI system parameter check 1:

PGM-FI system parameter check 1

?1.

Check the parameter(s) below with the HDS while pressing the clutch pedal.

NOTE:It may take a minimum of five seconds for the parameter to change.

Signal	Current conditions
Signal	Values	Unit
CLUTCH PEDAL POSITION SWITCH B

Does the parameter changes when the clutch is first pressed and then released?


	YES

Go to step 6.


	NO

Check the clutch pedal position switch B adjustment. If it is OK, go to step 3.

PGM-FI system parameter check 2:

PGM-FI system parameter check 2

?1.	Turn the vehicle to the OFF (LOCK) mode.

?2.

Disconnect the following connector.

Clutch pedal position switch B 6P connector

?3.

Connect terminals 1 and 2 with a jumper wire.

Terminal 1	Clutch pedal position switch B 6P connector No. 4
Terminal 2	Clutch pedal position switch B 6P connector No. 6

?4.	Turn the vehicle to the ON mode.

?5.

Check the parameter(s) below with the HDS.

Signal	Current conditions
Signal	Values	Unit
CLUTCH PEDAL POSITION SWITCH B

Does it indicate OPEN?


	YES

Replace the clutch pedal position switch B.?


	NO

Go to step 4.

Open wire check (GND line):

Open wire check (GND line)

?1.	Turn the vehicle to the OFF (LOCK) mode.

?2.

Connect terminals 1 and 2 with a jumper wire.

Terminal 1	Clutch pedal position switch B 6P connector No. 6
Terminal 2	Body ground

?3.	Turn the vehicle to the ON mode.

?4.

Check the parameter(s) below with the HDS.

Signal	Current conditions
Signal	Values	Unit
CLUTCH PEDAL POSITION SWITCH B

Does it indicate OPEN?


	YES

Repair an open in the wire between the clutch pedal position switch B and body ground (G302).?


	NO

The GND wire is OK, go to step 5.

Open wire check (CLUTCH SW (CRUISE) line):

Open wire check (CLUTCH SW (CRUISE) line)

?1.	Turn the vehicle to the OFF (LOCK) mode.

?2.	Short the SCS line with the HDS.

?3.

Disconnect the following connector.

PCM connector A (51P)

?4.

Check for continuity between test points 1 and 2.

Test condition	Vehicle OFF (LOCK) mode
	Clutch pedal position switch B 6P connector: disconnected
	PCM connector A (51P): disconnected
Test point 1	Clutch pedal position switch B 6P connector No. 6
Test point 2	PCM connector A (51P) No. 50

Is there continuity?


	YES

The CLUTCH SW (CRUISE) wire is OK. Update the PCM if it does not have the latest software, or substitute a known-good PCM, then retest.


	NO

Repair an open in the wire between the PCM and the clutch pedal position switch B.?

Clutch pedal position switch B performance check:

Clutch pedal position switch B performance check

?1.

Check the parameter(s) below with the HDS while pressing the clutch pedal.

NOTE:It may take a minimum of five seconds for the parameter to change.

Signal	Current conditions
Signal	Values	Unit
CRUISE CANCEL CLUTCH SWITCH STATUS

Does the parameter changes when the clutch is first pressed and then released?


	YES

Intermittent failure, the system is OK at this time. Refer to intermittent failures troubleshooting. If the freeze data/on-board snapshot of this DTC is recorded, try to reproduce the failure under the same conditions with the Freeze data/on-board snapshot.?


	NO

Go to step 7.

VSA modulator-control unit check (update):

VSA modulator-control unit check (update)

?1.	Update the VSA modulator-control unit if it does not have the latest software.

?2.	Turn the vehicle to the ON mode.

?3.

Check the parameter(s) below with the HDS while pressing the clutch pedal.

NOTE:It may take a minimum of five seconds for the parameter to change.

Signal	Current conditions
Signal	Values	Unit
CRUISE CANCEL CLUTCH SWITCH STATUS

Does the parameter changes when the clutch is first pressed and then released?


	YES

Troubleshooting is complete.?


	NO

Check for loose terminals in the VSA modulator-control unit 38P connector. If the VSA modulator-control unit was updated and the symptom/indication is still present, replace the VSA modulator-control unit.?