|
DTC Troubleshooting: B1659
DTC B1659: Front Interior LF Antenna Circuit Short
|
DTC Description |
DTC |
|
B1659 Front Interior LF Antenna Circuit Short |
| |
|
|
1. |
Problem verification:
Problem verification
|
?1. |
Clear the DTCs with the HDS.
|
|
?2. |
Select the MODE MENU from the HDS, then enter the SELF CHECK.
|
|
?4. |
Check for DTCs with the HDS.
|
DTC Description |
DTC |
|
B1659 Front Interior LF Antenna Circuit Short |
| |
| | |
Is DTC B1659 indicated?
|
|
|
|
|
|
|
Intermittent failure, the system is OK at this time. Check for loose or poor connections.? |
|
2. |
Shorted wire check (EXT F+, EXT F- lines):
Shorted wire check (EXT F+, EXT F- lines)
|
?1. |
Press the engine start/stop button to select the OFF mode. |
|
?2. |
Disconnect the following connectors.
|
|
?3. |
Check for continuity between test points 1 and 2 individually.
|
Test condition |
OFF mode
Keyless access control unit connector A (32P): disconnected
Front interior LF antenna 2P connector: disconnected |
|
Test circuit |
EXT F+ |
|
Test point 1 |
Keyless access control unit connector A (32P) No. 32 (GRN) |
|
Test point 2 |
Body ground | |
|
|
Test circuit |
EXT F- |
|
Test point 1 |
Keyless access control unit connector A (32P) No. 16 (BRN) |
|
Test point 2 |
Body ground | |
|
| |
Is there continuity?
|
|
|
Repair a short to ground in the wire.? |
|
|
|
The EXT F+ and EXT F- wires are not shorted. Go to step 3. |
|
3. |
Shorted wire check (EXT F+ line to EXT F- line):
Shorted wire check (EXT F+ line to EXT F- line)
|
?1. |
Check for continuity between test points 1 and 2.
|
Test condition |
OFF mode
Keyless access control unit connector A (32P): disconnected
Front interior LF antenna 2P connector: disconnected |
|
Test circuit |
EXT F+, EXT F- |
|
Test point 1 |
Keyless access control unit connector A (32P) No. 16 (BRN) |
|
Test point 2 |
Keyless access control unit connector A (32P) No. 32 (GRN) | |
|
| |
Is there continuity?
|
|
|
Repair a short in EXT F+ wire to EXT F- wire.? |
|
|
|
The EXT F+ and EXT F- wires are OK. Go to step 4. |
|
4. |
Determine possible failure area (Keyless access control unit, front interior LF antenna):
Determine possible failure area (Keyless access control unit, front interior LF antenna)
|
?1. |
Reconnect the following connectors.
|
|
?2. |
Press the engine start/stop button to select the ON mode. |
|
?3. |
Select KEYLESS ACCESS CONTROL from the ONE-PUSH START system select menu with the HDS, and enter FUNCTIONAL TESTS.
|
|
?4. |
Connect the voltmeter to test points 1 and 2.
|
Test point 1 |
Front interior LF antenna 2P connector No. 1 (BRN) |
|
Test point 2 |
Front interior LF antenna 2P connector No. 2 (GRN) | |
|
|
|
?5. |
Select CABIN FRONT ANTENNA with the HDS. | |
Is there voltage?
|