Keyless Access System Symptom Troubleshooting - The engine starts but stalls immediately
The engine starts but stalls immediately
1.
Keyless access system check 1:

Keyless access system check 1
?1.
Press the engine start/stop button to select the ON mode.

?2.
Check the immobilizer indicator.

Is the immobilizer indicator come on?

     
YES
     
     
     
Go to step 2.
     
NO
     
     
     
Go to step 4.
2.
Keyless access system check 2:

Keyless access system check 2
?1.
Check the immobilizer indicator.

Is the immobilizer indicator blinking?

     
YES
     
     
     
Go to step 3.
     
NO
     
     
     
Go to step 4.
3.
Keyless access system check 3:

Keyless access system check 3
?1.
Connect the HDS to the data link connector (DLC).

?2.
Select KEYLESS ACCESS CONTROL UNIT from the ONE-PUSH START system select menu with the HDS, and enter SYSTEM INFORMATION.

  

?3.
Do the SYSTEM CHECK 1 and 2 with the HDS.

Are N-1 OK and N-2 OK indicated?

     
YES
     
     
     
Go to step 4.
     
NO
     
     
     
Troubleshoot the keyless access system according to the result of the SYSTEM CHECK 1 and 2.?
4.
Gauge control module check:

Gauge control module check
?1.
Select GAUGES from the BODY ELECTRICAL SYSTEM SELECT menu with the HDS.

  

?2.
Select FUNCTIONAL TESTS from the TEST MODE menu with the HDS, and enter SELF TEST.

Does the immobilizer indicator come on?

     
YES
     
     
     
     
NO
     
     
     
5.
Keyless access system check 4:

Keyless access system check 4
?1.
With driver's power window open and all of the doors closed, press the engine start/stop button to select the OFF mode.

?2.
Remove all the keyless remotes from inside the vehicle. Hold them outside the open driver's window, at least 8.0 in (20 cm) away from the vehicle.

?3.
Press the enginestart/stop button.

?4.
Touch the engine start/stop switch with the keyless remote. The buttons on the keyless remote should be facing you.

?5.
Press the engine start/stop button to select the START mode.

Does the engine start?

     
YES
     
     
     
Go to step 6.
     
NO
     
     
     
Go to step 7.
6.
PGM-FI DTC check:

PGM-FI DTC check
?1.
Check for PGM-FI DTCs with the HDS.
DTC Description
Confirmed DTC
Pending DTC
     


Are any DTCs indicated?

     
YES
     
     
     
Troubleshoot the PGM-FI DTCs.?
     
NO
     
     
     
7.
Keyless access system check 5:

Keyless access system check 5
?1.
Select the IMMOBI from SYSTEM SELECTION MENU, then enter the IMMOBILIZER SETUP.

  

?2.
Select the SYSTEM CHECK from the IMMOBILIZER INFO.

Is SYSTEM CHECK indicated?

     
YES
     
     
     
Go to step 8.
     
NO
     
     
     
Troubleshoot the immobilizer system according to the result of the SYSTEM CHECK.?
8.
Keyless access control unit check (substitution):

Keyless access control unit check (substitution)
?1.
Substitute a known-good keyless access control unit.

?2.
Select REGISTRATION from the ONE-PUSH START system select menu with the HDS, then select REPLACE KEYLESS ACCESS CONTROL UNIT.

  

?3.
Press the engine start/stop button to select the ON mode.

Does the system change to ON mode?

     
YES
     
     
     
     
NO