DTC Troubleshooting: B1127
DTC B1127: Driver's Door Lock Key Cylinder Switch Malfunction
NOTE: If you are troubleshooting multiple DTCs, be sure to follow the instructions in B-CAN System Diagnosis Test Mode A.

DTC Description
DTC
B1127 Driver's Door Lock Key Cylinder Switch Malfunction
  

1.
Problem verification (driver's door key cylinder switch in the neutral position):

Problem verification (driver's door key cylinder switch in the neutral position)
?1.
Check the parameter(s) below with the HDS.
Signal
Current conditions
Values
Unit
Driver's Door Key Cylinder Switch(LOCK)
    
Driver's Door Key Cylinder Switch(UNLOCK)
    

Is either information indicator ON?

     
YES
     
     
     
Go to step 4.
     
NO
     
     
     
Go to step 2.
2.
Problem verification (driver's door key cylinder switch in the lock position):

Problem verification (driver's door key cylinder switch in the lock position)
?1.
With the driver's door key cylinder in the lock position, check the parameter(s) below with the HDS.
Signal
Current conditions
Values
Unit
Driver's Door Key Cylinder Switch(LOCK)
    
Driver's Door Key Cylinder Switch(UNLOCK)
    

Are both information indicators ON?

     
YES
     
     
     
Go to step 3.
     
NO
     
     
     
Intermittent failure, the system is OK at this time.
3.
Shorted wire check (DR KEY CYL UNLOCK to DR KEY CYL LOCK line):

Shorted wire check (DR KEY CYL UNLOCK to DR KEY CYL LOCK line)
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Disconnect the following connector.
Driver's door latch 10P connector

?3.
Connect terminals A and B with a jumper wire.
Terminal A
Power window master switch 37P connector No. 7
Terminal B
Body ground

?4.
Check the parameter(s) below with the HDS.
Signal
Current conditions
Values
Unit
Driver's Door Key Cylinder Switch(LOCK)
    
Driver's Door Key Cylinder Switch(UNLOCK)
    

Are both information indicators ON?

     
YES
     
     
     
Repair a short between the wires.?
     
NO
     
     
     
The DR KEY CYL UNLOCK to DR KEY CYL LOCK wire is OK. Faulty driver's door key cylinder switch; replace the driver's door latch.?
4.
Determine possible failure area (driver's door latch, others):

Determine possible failure area (driver's door latch, others)
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Disconnect the following connector.
Driver's door latch 10P connector

?3.
Check the parameter(s) below with the HDS.
Signal
Current conditions
Values
Unit
Driver's Door Key Cylinder Switch(LOCK)
    
Driver's Door Key Cylinder Switch(UNLOCK)
    

Is either information indicator ON?

     
YES
     
     
     
Go to step 5.
     
NO
     
     
     
Faulty driver's door key cylinder switch; replace the driver's door latch.?
5.
Shorted wire check (DR KEY CYL UNLOCK, DR KEY CYL LOCK lines):

Shorted wire check (DR KEY CYL UNLOCK, DR KEY CYL LOCK lines)
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Disconnect the following connector.
Power window master switch 37P connector

?3.
Check for continuity between test points 1 and 2 individually.
Test condition
Vehicle OFF (LOCK) mode
Driver's door latch 10P connector: disconnected
Power window master switch 37P connector: disconnected
Test point 1
Power window master switch 37P connector No. 7
Test point 2
Body ground

Test point 1
Power window master switch 37P connector No. 8
Test point 2
Body ground

Is there continuity?

     
YES
     
     
     
Repair a short to ground in the wire.?
     
NO
     
     
     
The DR KEY CYL UNLOCK and DR KEY CYL LOCK wires are OK. Replace the power window master switch.?.