NOTE: Front passenger's*1 is for 4-door, passenger's*2 is for 2-door.
1.
Keyless access system check:
Keyless access system check
?1.
Select KEYLESS ACCESS CONTROL UNIT from the ONE-PUSH START system select menu with the HDS, and enter HISTORY DATA.
?2.
Select HISTORY CLEAR, and back to TEST MODE menu:
NOTE: When the freeze data is cleared, the information indicates "NOT CONFIRMED".
DRIVER DOOR UNLOCK SWITCH
DRIVER DOOR LOCK SWITCH
FRONT PASSENGER DOOR UNLOCK SWITCH
FRONT PASSENGER DOOR LOCK SWITCH
?3.
Turn the vehicle to the OFF (LOCK) mode.
?4.
Get out of the vehicle with the keyless remote, and touch the each door outer handle touch sensor and push the lock button.
?5.
Select KEYLESS ACCESS CONTROL UNIT from the ONE-PUSH START system select menu with the HDS, and enter HISTORY DATA.
?6.
Recheck HISTORY DATA.
DRIVER DOOR UNLOCK SWITCH
DRIVER DOOR LOCK SWITCH
FRONT PASSENGER DOOR UNLOCK SWITCH
FRONT PASSENGER DOOR LOCK SWITCH
Is all the information OK?
YES
Intermittent failure, the system is OK at this time.?
NO
Go to step 2.
2.
Open wire check (GND line):
Open wire check (GND line)
?1.
Disconnect the following connectors.
Each door outer handle 8P connectors
?2.
Check for continuity between test points 1 and 2 individually.
Driver's door
Test condition
Vehicle OFF (LOCK) mode Driver's door outer handle 8P connector: disconnected
Test point 1
Driver's door outer handle 8P connector No. 8
Test point 2
Body ground
Front passenger's*1/passenger's*2 door
Test condition
Vehicle OFF (LOCK) mode Front passenger's*1/passenger's*2 door outer handle 8P connector: disconnected
Test point 1
Front passenger's*1/passenger's*2 door outer handle 8P connector No. 8
Test point 2
Body ground
Is there continuity?
YES
The GND wires are OK. Go to step 3.
NO
Repair an open or high resistance in the ground wire or poor ground (G501, G505).?
3.
Determine possible failure area (TS line, VOUT line):
Determine possible failure area (TS line, VOUT line)
?1.
Measure the voltage between test points 1 and 2 individually.
Driver's door
Test condition
Vehicle OFF (LOCK) mode Driver's door outer handle 8P connector: disconnected
Test point 1
Driver's door outer handle 8P connector No. 4
Test point 2
Body ground
Front passenger's*1/passenger's*2 door
Test condition
Vehicle OFF (LOCK) mode Front passenger's*1/passenger's*2 door outer handle 8P connector: disconnected
Test point 1
Front passenger's*1/passenger's*2 door outer handle 8P connector No. 4
Test point 2
Body ground
Is there battery voltage?
YES
Go to step 4.
NO
Go to step 7.
4.
Open wire check (TS FR DR, TS FR AS lines):
Open wire check (TS FR DR, TS FR AS lines)
?1.
Disconnect the following connector.
Body control module connector G (32P)
?2.
Connect terminals A and B with jumper wires.
Driver's door
Terminal A
Driver's door outer handle 8P connector No. 3
Terminal B
Body ground
Front passenger's*1/passenger's*2 door
Terminal A
Front passenger's*1/passenger's*2 door outer handle 8P connector No. 3
Terminal B
Body ground
?3.
Check for continuity between test points 1 and 2 individually.
Test condition
Vehicle OFF (LOCK) mode Each door outer handle 8P connectors: disconnected Each door outer handle 8P connectors: jumped to body ground Body control module connector G (32P): disconnected
