|
DTC Troubleshooting: B1645
DTC B1645: Driver Door LF Antenna Circuit Short
|
DTC Description |
DTC |
|
B1645 Driver's Door LF Antenna Circuit Short |
| |
|
|
1. |
Problem verification:
Problem verification
|
?1. |
Clear the DTCs with the HDS.
|
|
?2. |
Select the MODE MENU from the HDS, then enter the SELF CHECK.
|
|
?4. |
Check for DTCs with the HDS.
|
DTC Description |
DTC |
|
B1645 Driver's Door LF Antenna Circuit Short |
| |
| | |
Is DTC B1645 indicated?
|
|
|
|
|
|
|
Intermittent failure, the system is OK at this time. Check for loose or poor connections.? |
|
2. |
Shorted wire check (EXT FR DR+, EXT FR DR- lines):
Shorted wire check (EXT FR DR+, EXT FR DR- lines)
|
?1. |
Press the engine start/stop button to select the OFF mode. |
|
?2. |
Disconnect the following connectors.
|
|
?3. |
Check for continuity between test points 1 and 2 individually.
|
Test condition |
OFF mode
Keyless access control unit connector A (32P): disconnected
Driver's door outer handle 8P connector: disconnected |
|
Test circuit |
EXT FR DR+ |
|
Test point 1 |
Keyless access control unit connector A (32P) No. 29 (GRN) |
|
Test point 2 |
Body ground | |
|
|
Test circuit |
EXT FR DR- |
|
Test point 1 |
Keyless access control unit connector A (32P) No. 13 (BLU) |
|
Test point 2 |
Body ground | |
|
| |
Is there continuity?
|
|
|
Repair a short to ground in the wire.? |
|
|
|
The EXT FR DR+ and EXT FR DR- wires are not shorted. Go to step 3. |
|
3. |
Shorted wire check (EXT FR DR+ line to EXT FR DR- line):
Shorted wire check (EXT FR DR+ line to EXT FR DR- line)
|
?1. |
Check for continuity between test points 1 and 2.
|
Test condition |
OFF mode
Keyless access control unit connector A (32P): disconnected
Driver's door outer handle 8P connector: disconnected |
|
Test circuit |
EXT FR DR+, EXT FR DR- |
|
Test point 1 |
Keyless access control unit connector A (32P) No. 13 (BLU) |
|
Test point 2 |
Keyless access control unit connector A (32P) No. 29 (GRN) | |
|
| |
Is there continuity?
|
|
|
Repair a short in EXT FR DR+ wire to EXT FR DR- wire.? |
|
|
|
The EXT FR DR+ and EXT FR DR- wires are OK. Go to step 4. |
|
4. |
Determine possible failure area (Keyless access control unit, driver's door LF antenna):
Determine possible failure area (Keyless access control unit, driver's door LF antenna)
|
?1. |
Reconnect the following connectors.
|
|
?2. |
Press the engine start/stop button to select the ON mode. |
|
?3. |
Select KEYLESS ACCESS CONTROL from the ONE-PUSH START system select menu with the HDS, and enter FUNCTIONAL TESTS.
|
|
?4. |
Connect the voltmeter to test points 1 and 2.
|
Test point 1 |
Driver's door outer handle 8P connector No. 2 (GRN) |
|
Test point 2 |
Driver's door outer handle 8P connector No. 6 (BLU) | |
|
|
|
?5. |
Select DRIVER'S DOOR ANTENNA with the HDS. | |
Is there voltage?
|