Front Passengers Weight Sensor Removal and Installation

Front Passenger's Weight Sensor Removal and Installation

SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service.

NOTE:

Removal of the front passenger's weight sensors must be done according to Precautions and Procedures.

2-door: The front passenger's weight sensor is part of the seat frame and must be replaced as an assembly.

4-door: The front passenger's weight sensor is part of the seat rail and must be replaced as an assembly.

2-Door

1.	Battery Terminal - Disconnect

NOTE: Wait at least 3 minutes before starting work.

2.	Front Passenger's Seat Frame/Front Passenger's Weight Sensors - Remove

4-Door

1.	Battery Terminal - Disconnect

NOTE: Wait at least 3 minutes before starting work.

2.	Front Passenger's Seat - Remove

3.	Front Seat-Back Cover/Pad - Remove

4.	Front Seat Cushion Cover/Pad - Remove

5.	Front Seat Recline Inner Cover/Center Inner Cover - Remove

6.	Front Passenger's Seat Rail/Front Passenger's Weight Sensors - Remove

Power Seat

Manual Seat

Disconnect the connectors (A).

Remove the clips (B).

Remove the bolts (A).

Release the seat cushion springs (B) from the hooks (C), then remove the seat cushion frame (D).

Remove the nuts (A), then remove the front passenger's seat rail/front passenger's weight sensors as an assembly (B).

SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service.

NOTE:

Be sure to install the harness wires so they are not pinched or interfering with other parts.

2-door: The front passenger's weight sensor is part of the seat frame and must be replaced as an assembly.

4-door: The front passenger's weight sensor is part of the seat rail and must be replaced as an assembly.

2-Door

1.	Front Passenger's Seat Frame/Front Passenger's Weight Sensors - Install

2.	Battery Terminal - Connect

3.	Seat Operation - Confirm

Move the front seat and the seat-back through their full ranges of movement, making sure the harness are not pinched or interfering with other parts.

4.	Front Passenger's Weight Sensor - Initialize

5.	Front Passenger's Weight Sensor - Operation Check

6.	SRS Operation - Confirm

Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and check that the SRS indicator comes on for about 6 seconds and then goes off.

4-Door

1.	Front Passenger's Seat Rail/Front Passenger's Weight Sensors - Install

Power Seat

Manual Seat

Install the front passenger's seat rail/front passenger's weight sensors as an assembly (A) to the seat frame as shown, and loosely tighten the new nuts (B).

NOTE: The bushings and collars can be identified by their color. Make sure to install the bushings and collars as shown.

Tighten the nuts (A) to the specified torque.

NOTE: Tighten the nuts in the numbered sequence shown.

Install the seat cushion frame (A), and install the seat cushion springs (B) to the hooks (C).

Power Seat

Manual Seat

Connect the connectors (A).

Install the clips (B).

2.	Front Seat Recline Inner Cover/Center Inner Cover - Install

3.	Front Seat Cushion Cover/Pad - Install

4.	Front Seat-Back Cover/Pad - Install

5.	Front Passenger's Seat - Install

6.	Battery Terminal - Connect

7.	Seat Operation - Confirm

Move the front seat and the seat-back through their full ranges of movement, making sure the harness are not pinched or interfering with other parts.

8.	Front Passenger's Weight Sensor - Initialize

9.	Front Passenger's Weight Sensor - Operation Check

10.	SRS Operation - Confirm

Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode, and check that the SRS indicator comes on for about 6 seconds and then goes off.