DTC Troubleshooting: B0001-11

DTC B0001-11: Short to Ground in the Driver's Airbag First Inflator

NOTE:

	Before doing this troubleshooting procedure, find out if the vehicle was in a collision. If so, verify that all the required components were replaced with new components of the correct part number and were properly installed.
	Before doing this troubleshooting procedure, review SRS Precautions and Procedures, General Troubleshooting Information, and 12 Volt Battery Terminal Disconnection and Reconnection.
	Before replacing the SRS unit, check the SRS unit software version with the HDS. If the software version is not the latest, update the SRS unit software, and retest.

DTC Description	DTC
B0001-11 Short to ground in the driver's airbag first inflator

Problem verification:

Problem verification

?1.	Clear the DTCs with the HDS.

?2.	Turn the vehicle to the ON mode, then wait for 10 seconds.

?3.

Check for DTCs with the HDS.

DTC Description	DTC
B0001-11 Short to ground in the driver's airbag first inflator

Is DTC B0001-11 indicated?


	YES

The failure is duplicated. Go to step 2.


	NO

Intermittent failure, the system is OK at this time. Go to Troubleshooting Intermittent Failures. If another DTC is indicated, troubleshoot the DTC.?

Shorted wire check (LA1?, LA1? lines) 1:

Shorted wire check (LA1?, LA1? lines) 1

?1.	Turn the vehicle to the OFF (LOCK) mode.

?2.	Disconnect the negative cable from the 12 volt battery, then wait at least 3 minutes.

?3.

Disconnect the following connector.

SRS unit connector A (39P)

?4.

Measure the resistance between test points 1 and 2.

Test condition	Vehicle OFF (LOCK) mode
Test condition	SRS unit connector A (39P): disconnected
Test point 1	SRS unit connector A (39P) No. 9
Test point 2	Body ground

Test point 1	SRS unit connector A (39P) No. 8
Test point 2	Body ground

Is there an open circuit, or at least 1 M??


	YES

The LA1? and LA1? wires are OK. Replace the SRS unit.?


	NO

Go to step 3.

Shorted wire check (LA1?, LA1? lines) 2:

Shorted wire check (LA1?, LA1? lines) 2

?1.	Remove the driver's airbag.

?2.

Disconnect the following connector.

Driver's airbag first inflator 2P connector (on the cable reel harness)

?3.

Measure the resistance between test points 1 and 2.

Test condition	Vehicle OFF (LOCK) mode
	SRS unit connector A (39P): disconnected
	Driver's airbag first inflator 2P connector (on the cable reel harness): disconnected
Test point 1	SRS unit connector A (39P) No. 9
Test point 2	Body ground

Test point 1	SRS unit connector A (39P) No. 8
Test point 2	Body ground

Is there an open circuit, or at least 1 M??


	YES

The LA1? and LA1? wires are OK. Faulty driver's airbag first inflator; replace the driver's airbag, then clear the DTC.?


	NO

Go to step 4.

Shorted wire check (LA1?, LA1? lines) 3:

Shorted wire check (LA1?, LA1? lines) 3

?1.	Remove the column covers.

?2.	Disconnect cable reel connector B (4P) on the dashboard wire harness.

?3.

Measure the resistance between test points 1 and 2.

Test condition	Vehicle OFF (LOCK) mode
	SRS unit connector A (39P): disconnected
	Driver's airbag first inflator 2P connector (on the cable reel harness): disconnected
	Cable reel connector B (4P) (on the dashboard wire harness): disconnected
Test point 1	SRS unit connector A (39P) No. 9
Test point 2	Body ground

Test point 1	SRS unit connector A (39P) No. 8
Test point 2	Body ground

Is there an open circuit, or at least 1 M??


	YES

The LA1? and LA1? wires are OK. Short to ground in the cable reel; replace the cable reel, then clear the DTC.?


	NO

Short to ground in the dashboard wire harness; replace the dashboard wire harness, then clear the DTC.?